Whirlpool JIC4536XB Instruction for Use

Browse online or download Instruction for Use for Security device components Whirlpool JIC4536XB. Whirlpool KICU569XBL Instruction for Use User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 16
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
FOR SERVICE TECHNICIAN’S USE ONLY
Acronyms and Abbreviations
PC: Power Control Board
NTC: Negative Temperature Coefficient
UI: User Interface board
Manual Configuration Mode
To Enter Manual Configuration Mode:
NOTE: This menu is accessible only during the first minutes after the
cooktop is plugged in.
1. Remove the key-lock functionality by pressing the Control Lock
button.
2. Press the following keys sequentially (a beep will sound after each key
press): Timer “-”, Timer “+”, Timer “-”, Timer “+”, Control Lock.
After the keystroke combination is pressed, a “CO” will appear on the
display.
3. Press the Control Lock button.
An “00” will appear on the display.
4. Configure the correct cooktop model number by choosing one of the
following numbers.
Use the Timer buttons to see different numbers on the display, moving
sequentially and beginning at “00.” The Timer “+” button will increase
the number by 1, and the Timer “-” button will decrease the number
by 1.
5. Press the Control Lock button to confirm the configuration. The
configuration will then be downloaded into the cooktop.
This process will last a few seconds. The number of the cooktop
chosen will blink on the display. The cooktop will restart with the new
configuration written.
6. The cooktop is ready to use.
501961902035 FOR SERVICE TECHNICIAN’S USE ONL
Y
DANGER
Electrical Shock Hazard
Only authorized technicians should perform diagnostic
voltage measurements.
After performing voltage measurements, disconnect
power before servicing.
Failure to follow these instructions can result in death
or electrical shock.
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
Voltage Measurement Safety Information
When performing live voltage measurements, you must do the following:
Verify the controls are in the off position so that the appliance does not start when energized.
Allow enough space to perform the voltage measurements without obstructions.
Keep other people a safe distance away from the appliance to prevent potential injury.
Always use the proper testing equipment.
After voltage measurements, always disconnect power before servicing.
Tech Sheet Do not discard
Configuration Number Cooktop
23 KICU509X
24 JIC4430X
25 JIC4536X
26 KICU569X
Page view 0
1 2 3 4 5 6 ... 15 16

Summary of Contents

Page 1 - Manual Configuration Mode

FOR SERVICE TECHNICIAN’S USE ONLYAcronyms and Abbreviations PC: Power Control Board NTC: Negative Temperature Coefficient UI: User Interface boardM

Page 2 - Failure/Error Codes

10À L'USAGE DU TECHNICIEN DE RÉPARATION UNIQUEMENTF-25 Ventilateur bloqué sur la carte de commande de puissance (ventilateur droit ou gauche selo

Page 3

11À L'USAGE DU TECHNICIEN DE RÉPARATION UNIQUEMENTF-42 Alimentation électrique Type 2 1. Vérifier que la tension au raccordement principal de l’a

Page 4 - Component Testing Chart

12À L'USAGE DU TECHNICIEN DE RÉPARATION UNIQUEMENTTableau de test des composantsPour contrôler une tension correcte, procéder aux étapes suivante

Page 5 - CONNECTOR NOTE:

13À L'USAGE DU TECHNICIEN DE RÉPARATION UNIQUEMENTSchéma de câblageModèles de 30" (76,2 cm) LégendeJ1 - Connecteur principal

Page 6

14À L'USAGE DU TECHNICIEN DE RÉPARATION UNIQUEMENTModèles de 36" (91,4 cm) LégendeJ1 - Connecteur principal d'alimentati

Page 7 - 30" (76.2 cm) Cooktop

15À L'USAGE DU TECHNICIEN DE RÉPARATION UNIQUEMENTComposants de la table de cuisson à inductionTable de cuisson de 30" (76,2 cm)A. Glissière

Page 8 - AVERTISSEMENT

À L'USAGE DU TECHNICIEN DE RÉPARATION UNIQUEMENTTable de cuisson de 36" (91,4 cm)A. Panneau étancheB. GlissièreC. Conduit de ventilationD. M

Page 9 - Codes d’anomalie/erreur

2FOR SERVICE TECHNICIAN’S USE ONLYFailure/Error CodesIf all the lights on the User Interface are Off and there is no response from the cooktop, comple

Page 10

3FOR SERVICE TECHNICIAN’S USE ONLYF-36, F37 Temperature sensor is not working Type 1 1. Disconnect power.2. Check that the temperature sensor is betwe

Page 11

4FOR SERVICE TECHNICIAN’S USE ONLYComponent Testing ChartTo check for proper voltage, complete the following steps:1. Disconnect power.2. Connect volt

Page 12

5FOR SERVICE TECHNICIAN’S USE ONLYWiring Diagrams30" (76.2 cm) models LegendJ1 - Filter Main Power Connector 1J2 - Filter Main Pow

Page 13 - Modèles de 30" (76,2 cm)

6FOR SERVICE TECHNICIAN’S USE ONLY36" (91.4 cm) models LegendJ1 - Filter Main Power Connector 1J2 - Filter Main Power Connector 2I

Page 14 - Modèles de 36" (91,4 cm)

7FOR SERVICE TECHNICIAN’S USE ONLYInduction Cooktop Components30" (76.2 cm) Cooktop36" (91.4 cm) CooktopA. Slider plateB. Duct fanC. FoamD.

Page 15

8À L'USAGE DU TECHNICIEN DE RÉPARATION UNIQUEMENTAcronymes et abréviations PC : Carte de commande de puissance NTC : coefficient de température

Page 16 - 501961902035

9À L'USAGE DU TECHNICIEN DE RÉPARATION UNIQUEMENTCodes d’anomalie/erreurSi tous les témoins de l’interface utilisateur sont éteints et en l’absen

Comments to this Manuals

No comments