Whirlpool Whispure Air Purifier User Manual download pdf (Page 5)

Using the Controls

1. Plug into a grounded 3 prong outlet.

2. Press POWER to start the air purifier. An indicator light will

turn on.

3. Press POWER to stop the air purifier. The indicator light will

turn off.

Fan Speed

Press FAN SPEED until the indicator light comes on for the

desired speed.

Sleep Mode

Press SLEEP MODE to set. Sleep mode runs on Low fan speed

for 8 hours and then returns to previously selected setting. To exit

before 8 hours, press SLEEP MODE, FAN SPEED, or POWER.

Control Lock

The Control Lock locks the controls to prevent unintended

changing of the settings when the air purifier is on or off.

1. Press and hold SLEEP MODE for 5 seconds to lock. The

Control Lock indicator light will turn on. (No selection can be

made.)

2. Press SLEEP MODE for 5 seconds to unlock. The Control

Lock indicator light will turn off. Now selections can be made

and the unit can be turned on or off.

Filter Status Lights

The pre-filter and HEPA filter status lights will help you know

when to change your filters. The green status lights will move

from New to Replace at preset intervals. When the red Replace

status light is flashing, replace the filter as indicated. See “Filter

Replacement” in the “Air Purifier Care” section.

AIR PURIFIER CARE

Cleaning

1. Press POWER to turn off the air purifier.

2. Unplug air purifier or disconnect power.

3. Place fingers on the front release tabs. Gently push the tabs

in and pull the front grille forward to remove it.

4. Remove both filters and set aside. Do not try to wash and

reuse either the HEPA filter or the pre-filter.

5. Clean the air purifier with a soft, damp cloth.

6. Gently wash the front grille in soapy water.

NOTE: The grille is not dishwasher safe.

7. Reassemble the filters as shown in previous illustration.

8. Place the bottom tabs on the front grille into the bottom slots

in base of the air purifier. Push the top of the grille forward

until the grille locks into place.

9. Plug in air purifier or reconnect power.

10. Press POWER to start the air purifier.

Filter Replacement

NOTE: The filter indicator lights on top of the air purifier will glow

when it is time to replace either the pre-filter or the HEPA filter.

For the most efficient operation of the air purifier, under normal

conditions it is recommended that you replace the pre-filter every

3 months and the HEPA filter every year. See “Replacement

Filters” in the “Assistance or Service” section.

1. Press POWER to turn off the air purifier.

2. Unplug air purifier or disconnect power.

3. Place fingers on the front release tabs. Gently push the tabs

in and pull the front grille forward to remove it.

4. Remove and replace the indicated filter. Install the new HEPA

filter in the same direction shown by the arrow located on the

filter frame. Install the new pre-filter by placing it on the tabs.

NOTE: Do not try to wash and reuse either the HEPA filter or

the pre-filter.

5. Place the bottom tabs on the front grille into slots in the base

of the air purifier. Push the top of the grille forward until the

grille locks into place.

FAN SPEED RESULT

Low

Medium

High

Turbo

Best product sound

Slower cleaning power

Moderate cleaning power

Maximum cleaning power

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Failure to follow these instructions can result in

death, fire, or electrical shock.

Do not use an extension cord.

Do not use an adapter.

Do not remove ground prong.

A. Release tabs

B. Controls

C. Front grille

D. Pre-filter

E. HEPA filter

F. Bottom slot

G. Mainframe assembly

CDE

1 2 3 4 5 6 7 8 9 10 ... 19 20

Comments to this Manuals

No comments

Whirlpool Whispure Air Purifier User Manual Page 5

Comments to this Manuals