Whirlpool GSF26C4EXB User Manual download pdf (Page 9)

Installing the Filter Status Indicator (on some models)

The filter comes with a status indicator, which should be activated

and installed at the same time the air filter is installed.

1. Place the indicator face-down on a firm, flat surface.

2. Apply pressure to the bubble on the back of the indicator, until

the bubble pops to activate the indicator.

3. Lift open the vented air filter door. On some models, there are

notches along the rear wall, behind the bottom-left corner of

the door.

4. On models with notches:

■ Slide the indicator down into the notches, facing outward.

NOTE: The indicator will not easily slide into the notches

if the rear bubble has not been popped.

■ Close the air filter door, and check that the indicator is

visible through the rectangular hole in the door.

On models without notches:

■ Store the indicator in a visible place you will easily

remember - either inside the refrigerator, or elsewhere in

your kitchen or home.

Replacing the Air Filter

The disposable air filter should be replaced every 6 months, when

the status indicator has completely changed from white to red.

To order a replacement air filter, contact us using the

assistance/service information following the warranty.

1. Remove the old air filter by squeezing in on the side tabs.

2. Remove the old status indicator.

3. Install the new air filter and status indicator using the

instructions in the previous sections.

REFRIGERATOR USE

Using the Controls

The refrigerator and freezer controls are located on the dispenser

panel.

IMPORTANT: The display screen on the dispenser control panel

will turn off automatically and enter “sleep” mode when the

control buttons and dispenser levers have not been used for

2 minutes or more. While in “sleep” mode, the first press of a

control button will only reactivate the display screen, without

changing any settings. After reactivation, changes to any settings

can then be made. If no changes are made within 2 minutes, the

display will re-enter “sleep” mode.

■ Touch any control button on the dispenser panel to activate

the display screen. The home screen will appear as shown.

Adjusting the Controls

For your convenience, your refrigerator and freezer controls are

preset at the factory. When you first install your refrigerator, make

sure that the controls are still set to the “mid-settings.” The factory

recommended set points are 37°F (3°C) for the refrigerator and

0°F (-18°C) for the freezer.

IMPORTANT:

■ Wait 24 hours before you put food into the refrigerator. If you

add food before the refrigerator has cooled completely, your

food may spoil.

NOTE: Adjusting the set points to a colder than

recommended setting will not cool the compartments any

faster.

■ If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not

blocked before adjusting the controls.

■ The preset settings should be correct for normal household

usage. The controls are set correctly when milk or juice is as

cold as you like and when ice cream is firm.

■ Wait at least 24 hours between adjustments. Recheck the

temperatures before other adjustments are made.

To view and adjust the set points, press and hold the TEMP

button for 3 seconds. When adjust mode is activated, adjusting

information will appear on the display screen.

NOTE: To view Celsius temperatures, press the LIGHT button

when adjust mode is activated. To return the display setting to

Fahrenheit, press LIGHT again.

■ When adjust mode is activated, the display screen shows the

refrigerator set point and “FRIDGE” appears.

■ Press LOCK to raise the set point, or press FAST ICE to lower

the set point.

■ When you have finished viewing (and adjusting if desired) the

refrigerator set point, press TEMP to change the display to

show the freezer set point. When the zone has been changed,

“FREEZER” appears on the display screen.

■ Press LOCK to raise the set point, or press FAST ICE to lower

the set point.

MONTHS

REPLACE

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 59 60

Comments to this Manuals

No comments

Modely	Typ Dokumentu
HC3418/15	Datový list Philips HC3418, 3 stránky
HC7450/16	Datový list Philips 7000 series HC7450, 3 stránky
HC5446/80	Datový list Philips HC5446, 3 stránky
HC5438/15	Datový list Philips HC5438, 3 stránky
HC7460/15	Datový list Philips HC7460, 3 stránky
HC5438/80	Datový list Philips HC5438, 3 stránky
HC5446/15	Datový list Philips HC5446, 3 stránky
BT7085/32	Datový list Philips BEARDTRIMMER Series 7000 Vacuum stubble and beard trimmer BT7085/32, 3 stránky
QC5370/15	Datový list Philips HAIRCLIPPER Series 5000 hair clipper QC5370, 2 stránky
BT5260/32	Datový list Philips BT5260/32, 3 stránky
HC5440/80	Datový list Philips HAIRCLIPPER Series 5000 HC5440, 86 stránky
QT4023/32	Datový list Philips Stubble trimmer QT4023/32, 2 stránky
QC5360/32	Datový list Philips hair clipper QC5360, 2 stránky
QC5360/15	Datový list Philips HAIRCLIPPER Series 5000 hair clipper QC5360, 2 stránky
QC5360/31	Datový list Philips QC5360/31, 2 stránky
QC5105/15	Datový list Philips hair clipper QC5105, 2 stránky
QC5375/80	Datový list Philips hair clipper QC5375, 2 stránky
QC5315/15	Datový list Philips hair clipper QC5315, 2 stránky
QC5550/15	Datový list Philips Do-It-Yourself clipper hair clipper QC5550/15, 3 stránky
QC5130/15	Datový list Philips hair clipper QC5130, 2 stránky

Whirlpool GSF26C4EXB User Manual Page 9

Comments to this Manuals

Philips QC5126/15 manuály

Philips QC5126/15 Datový list (3 strany)

Tabulka s obsahem

Další produkty a příručky pro Zastřihovače vlasů Philips

Whirlpool GSF26C4EXB User Manual Page 9

Comments to this Manuals

Related products and manuals for Fridges Whirlpool GSF26C4EXB

Philips QC5126/15 manuály

Philips QC5126/15 Datový list (3 strany)

Tabulka s obsahem

Další produkty a příručky pro Zastřihovače vlasů Philips