Whirlpool Ice Maker User Manual download pdf

Parts

Use listed part numbers only when ordering replacement

parts. Part number are not used in installation instructions.

Item Description Part number

1 Ice maker D7824703

2 Ice maker cover 10519801

" long sheet metal screw (to

secure ice maker)

M0211118

4 Stainless steel clip B5720302

5 Ice maker wire harness clamp 10526701

6 Ice maker wire harness D7813004

7 Ice maker arm 10884401

8 Button plug M0311301

9 Oblong plug A3124301

10 Thermal fuse clip (attached to

ice maker)

10319801

11 Plastic clips (4) M0104106

12 Ice storage bucket 10476201

13 Compression nut and sleeve 10244904

N/S Warning level (attached to side

of ice maker)

A3036901

N/S Diagnostic label (inside ice

maker cover)

10834701

N/S Installation Instructions 10527033

N/S= Not shown

Introduction

Recognize this symbol as a

safety precaution.

Read entire manual before installing kit. All necessary tools

and materials must be available prior to installation. Verify

all listed parts are included in kit. If parts are missing,

contact source from whom kit was purchased.

• Mechanical experience is required to install kit.

• If unable to solve a problem during installation, contact

an authorized Amana technician. Locate a Factory

Service Center or independent authorized technician by

calling 1-800-628-5782 inside U.S.A. and 1-319-622-

5511 outside U.S.A. Service is at owner’s expense.

Safety Instructions

WARNING

To avoid electrical shock which can cause severe

personal injury or death, unplug power cord or open

household circuit breaker to refrigerator before installing

kit. After installing kit, reconnect power.

Caution

To avoid property damage, observe the following:

• Confirm water pressure to water valve is at least 20

pounds per square inch.

• Start nuts by hand to avoid cross threading. Finish

tightening nuts using a wrench. Do not overtighten.

• Check carefully for water leaks prior to returning

refrigerator to normal location and 24 hours after

connection.

Before Connecting Ice Maker

Important

• Before connecting ice maker, contact a plumber to

connect copper tubing for refrigerator water supply to

household plumbing in compliance with local codes and

ordinances.

Use

/4" (6 mm) flexible copper tubing. Length of copper

tubing must reach from water supply connection plus an

additional 8' (2.5 m) for service loop behind refrigerator.

Tubing should be soft instead of rigid and ends should be

free of burrs.

Copper tubing route must be above 35°F (2°C) to prevent

water line from freezing.

IC8 Top and Bottom Freezer Refrigerator Ice Maker Kit

Installation and Operating Instructions

1 2 3 4

Summary of Contents

Page 1

PartsUse listed part numbers only when ordering replacementparts. Part number are not used in installation instructions.12389741056111213Item Descript

Page 2 - Caution

Do not use piercing type or 3/16" saddle valves! Both reducewater flow, become clogged with time and may cause leaksover time if repair is attemp

Page 3 - Install Ice Maker

ClipsInstall Ice Maker1. Remove any shelves that may obstruct installation ofice maker module.Models with ice service rackSlide ice service rack towar

Page 4 - Before Calling For Service

! CautionTo avoid property damage, all covers must be in place.12. Plug in refrigerator and move refrigerator in place. Levelif necessary.13. Check f

Comments to this Manuals

No comments

Whirlpool Ice Maker User Manual

Browse online or download User Manual for Ice cube makers Whirlpool Ice Maker. IC8 Top and Bottom Freezer Refrigerator Ice Maker Kit [en]

Summary of Contents

Comments to this Manuals

Related products and manuals for Ice cube makers Whirlpool Ice Maker