Whirlpool W10197087 User Manual download pdf

INSTRUCTION SHEET FOR BUILT-IN REFRIGERATOR

HANDLE ACCESSORY

BEFORE YOU BEGIN: The handle and handle mounting hardware must be installed before installing the custom panel. A qualified

cabinetmaker must perform the installation.

IMPORTANT: Do not use these handle(s) on acrylic panels.

TOOLS NEEDED:

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

PARTS SUPPLIED:

* (#) represents quantities for French door bottom mount freezer

models.

Install the refrigerator handle

IMPORTANT: See Figure 1 and the Refrigerator Door table for

handle mounting hole requirements as well as handle mounting

hole locations.

1. Measure from the bottom of the custom panel and mark your

first hole location as shown in Figure 1 and Refrigerator Door

table.

Figure 1: Refrigerator door

NOTE: Measurements from the side edge of the door will

depend on specific application.

2. Drill a ³⁄₁₆" (4.76 mm) hole at that location, then measure up

from the bottom hole to determine the location of the second

hole. Countersink both holes on the inside of the panel, ¹⁄₄"

(6.35 mm) deep and ⁵⁄₈" (1.58 cm) diameter for screw head

clearance.

3. Install two mounting studs to the custom panel using the

screws provided. Check that the head of the screw is flush

with the panel.

4. Install handle to handle mounting studs and tighten the

setscrews. Some adjustments of the handle mounting studs

may be required to allow the handle to fit over both mounting

studs.

NOTE: For products with one refrigerator door, the setscrew

should face the hinge side of the door. For products with two

refrigerator doors, the setscrews should face the center of the

product.

5. If you have two doors, repeat steps 1-4.

■ Cordless drill

■ ⁵⁄₁₆" socket driver

■ ³⁄₃₂" Allen wrench

■ Drill bits

■ Flat-blade screwdriver

■ Tape measure

■ Pencil

■ Handle - freezer door

■ Handle - refrigerator

door (2)*

■ 4 Studs - handle

mounting (6)*

■ 4 Screws - #10-24 x 1"

hex washer head (6)*

Refrigerator Door

Dimension Bottom Mount

Freezer

French Door Bottom

Mount Freezer

Euro handle Pro handle Euro handle Pro handle

A9³⁄₄"9³⁄₄"9⁷⁄₈"9⁷⁄₈"

B 30" 30" 30" 30"

Handle

Mounting

Studs

Refrigerator

Compartment

Handle

Custom Refrigerator

Compartment Panel

Setscrews

#10-24 x 1" Screws

W10194026A

1 2 3 4

Summary of Contents

Page 1 - HANDLE ACCESSORY

INSTRUCTION SHEET FOR BUILT-IN REFRIGERATORHANDLE ACCESSORYBEFORE YOU BEGIN: The handle and handle mounting hardware must be installed before installi

Page 2 - Install the freezer handle

2Install the freezer handleIMPORTANT: See Figure 2 and the Freezer Door table for handle mounting hole requirements as well as handle mounting hole lo

Page 3 - POIGNÉE ACCESSOIRE

3FICHE D'INSTRUCTIONS POUR RÉFRIGÉRATEUR ENCASTRÉPOIGNÉE ACCESSOIREAVANT DE COMMENCER : La poignée et les pièces de montage de la poignée doivent

Page 4

Installation de la poignée du congélateurIMPORTANT : Voir la figure 2 et le tableau (Porte du congélateur) pour les spécifications de trous de montage

Comments to this Manuals

No comments

Whirlpool W10197087 User Manual

Browse online or download User Manual for Refrigerators Whirlpool W10197087. Whirlpool W10197087 Manuel d'utilisation

Summary of Contents

Comments to this Manuals

Related products and manuals for Refrigerators Whirlpool W10197087