Whirlpool Duet W10110850A User Manual

ELECTRONICELECTRIC DRYERUse & Care GuideFor questions about features, operation/performance, parts, accessories or service, call: 1-800-253-1301or

10 Put power supply cord through the strain relief. Be sure that the wire insulation on the power supply cord is inside the strain relief. The strain

112. Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and the neutral wire (white or center wire) of power

123. Connect ground wire (green or bare) of direct wire cable to external ground conductor screw. Tighten screw.4. Place the hooked ends of the other

13When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right), squeeze hooked en

14Venting RequirementsWARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS.IMPORTANT: Observe all governing codes and ordinances

15Plan Vent SystemChoose your exhaust installation typeRecommended exhaust installationsTypical installations vent the dryer from the rear of the drye

16Special provisions for mobile home installationsThe exhaust vent must be securely fastened to a noncombustible portion of the mobile home structure

172. Firmly grasp the body of the dryer (not the console panel). Gently lay the dryer on the cardboard. See illustration. 3. Examine the leveling l

18DRYER USEStarting Your DryerWARNING: To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before

19 Press and hold START button until dryer starts (about 1 second).Once an Automatic cycle has started, the WRINKLE SHIELD™ feature and cycle signals

2TABLE OF CONTENTSDRYER SAFETY...3INSTALLATION INSTRUCTIONS...

20 Remove the load from the dryer as soon as tumbling stops to reduce wrinkling. This is especially important for permanent press, knits and syntheti

21Damp DryUse this cycle to dry items to a damp level using Low heat. Damp dry items such as jeans (to avoid stiffness) or cotton clothing (to make ir

22 For the Casual Cycle, the WRINKLE SHIELD™ feature is preset to “ON.” The other cycles will retain the WRINKLE SHIELD™ feature setting. (For exampl

23Drying Rack OptionThe drying rack is useful for drying items you would not necessarily want to tumble dry or that you would normally line dry (for e

24IMPORTANT: Do not run the dryer with the lint screen loose, damaged, blocked, or missing. Doing so can cause overheating and damage to both the dry

25TROUBLESHOOTINGFirst try the solutions suggested here and possibly avoid the cost of a service call...Dryer OperationDryer will not run Has a house

26 Is the dryer located in a room with temperature below45ºF (7ºC)? Proper operation of dryer cycles requires temperatures above 45ºF (7ºC). Is the

27ASSISTANCE OR SERVICEBefore calling for assistance or service, please check “Troubleshooting.” It may save you the cost of a service call. If you st

WHIRLPOOL CORPORATION MAJOR APPLIANCE WARRANTYONE YEAR LIMITED WARRANTYFor one year from the date of purchase, when this major appliance is operated a

3DRYER SAFETYYou can be killed or seriously injured if you don't immediately You can be killed or seriously injured if you don'tfollow All

4INSTALLATION INSTRUCTIONSTools and PartsGather the required tools and parts before starting installation. Read and follow the instructions provided w

5Stack KitAre you planning to stack your DUET® washer and dryer? To do so, you will need to purchase a Stack Kit.To order, call the dealer from whom y

6Dryer Dimensions*Most installations require a minimum 5" (12.7 cm) clearance behind the dryer for the exhaust vent with elbow. See “Venting Re

7Recommended installation spacing for recessed or closet installation, with stacked washer and dryer The dimensions shown are for the recommended spa

8If using a power supply cord:Use a UL listed power supply cord kit marked for use with clothes dryers. The kit should contain: A UL listed 30-amp po

9Electrical Connection1. Disconnect power.2. Remove the hold-down screw and terminal block cover. 3. Install strain relief.Style 1: Power supply cord