Whirlpool WRF757SDEH Installation Guide

Browse online or download Installation Guide for Unknown Whirlpool WRF757SDEH. Whirlpool WRF757SDEH Installation Guide User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 2
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
GETTING STARTED
SAVE THESE AND ALL INSTRUCTIONS! For more details and additional important information, see the other instructions provided inside your refrigerator.
W10325092D 12/14
© 2014. All rights reserved. Printed in U.S.A.
TOOLS REQUIRED
Depending on the width of the door opening, the following tools
may be required to remove, replace, and align the refrigerator
doors.
Tools Needed:
#2 Phillips screwdriver – Top hinge cover screws
Torx
®†
T25 screwdriver – Top and center hinge screws
¹⁄₄" Hex nut or socket driver – Drawer screws and brake feet
³⁄₈" Socket or Torx
®†
T25 screwdriver – Brake feet bracket
screws
Tools Provided:
¹⁄₈" Hex key – Handle setscrews and door alignment screw
INSTALLATION CHECKLIST
Electrical Power
Plug refrigerator into a grounded 3 prong outlet.
Doors
If doors need to be removed during installation, see the
“Remove and Replace Doors” section in the instructions.
Check that handles are secure and installed according to
the instructions.
Doors seal completely
Refrigerator is level (Remove base grille and adjust leveling
feet so they are snug against the floor)
Doors are even across the top (Use door alignment feature
if necessary)
Base grille is properly attached to the refrigerator
Ice and Water System (on some models)
Connect refrigerator to a cold water supply with adequate
water pressure, as specified in the instructions.
Make sure the household water supply is connected and
turned on.
Check that the water supply line behind refrigerator is not
kinked.
Use recommended water supply tubing only as specified in
the instructions.
Install water filter according to the instructions.
Flush water system according to instructions.
Check for water leaks at all connections.
Turn on ice maker if refrigerator is connected to water
supply. (If not connected to water supply, turn off ice maker.)
Final Checks
Remove all shipping material.
Set temperature controls to the recommended setting.
Save instructions and other literature.
Send in Registration Card or register your product online.
†®TORX is a registered trademark of Acument Intellectual
Properties, LLC.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
LEVELING AND DOOR ALIGNMENT
(AFTER MOVING TO FINAL LOCATION)
To view an animated video about the
leveling and door alignment process, scan
the code at left with your mobile device.
To steady or adjust the tilt of the refrigerator, you must first
remove the base grille.
Grasp the base grille firmly and pull it toward you to
remove. Open the freezer drawer.
Steady the Refrigerator
If the refrigerator seems unsteady or rolls when the door(s) or
drawer(s) are pulled open.
Use a ¹⁄₄" hex nut driver to turn both brake feet clockwise
the same amount until they are snug against the floor.
Adjust Tilt
If the refrigerator doors do not close easily, or pop open.
Use a ¹⁄₄" hex nut or socket driver to turn both brake feet
clockwise the same amount. This will raise the front of the
refrigerator.
NOTE: Having someone push against the top of the
refrigerator takes some weight off the brake feet, making it
easier to turn the feet.
A. Brake foot
Align Refrigerator Doors
If doors are uneven.
Keep both refrigerator doors closed. Open the drawer
directly under the doors.
Insert ¹⁄₈" hex key wrench into the bottom hinge pin located
at the bottom of the right-hand refrigerator door.
Turn key to the right to raise the refrigerator door.
Turn key to the left to lower the refrigerator door.
A. Bottom hinge pin
B. ¹⁄₈" Hex key wrench
Lower
Raise
A
B
¹⁄₄"
A
WATER FILTER INSTALLATION
Locate the water filter compartment in the right-hand side of
the refrigerator ceiling. Push upward on compartment door to
open.
Align the arrow on the water filter label with the cutout notch in
the filter housing and insert filter.
Once the filter is inserted, turn the filter clockwise 90° (
1
4 turn),
until it locks into the housing. Lift filter into compartment and
close door.
Flush the water system to clear air from the water line and to
keep the dispenser from dripping, and/or avoid decreased
dispenser flow.
NOTE: If the filter is not installed correctly, water will not be
dispensed.
ICE MAKER ON/OFF SWITCH
Models with Ice Storage Bin on Door
Open the left-hand refrigerator door.
Open the ice storage bin door.
Locate the ice maker switch on left wall of bin area.
A. Ice storage bin release latch
Models with Ice Storage Bin in Freezer
Open the freezer drawer.
Locate the wire shutoff arm.
Arm lowered – ON, Arm up – OFF
A
PRODUCE PRESERVER INSTALLATION
(on some models)
Install Produce Preserver(s) and status indicator(s) according
to instructions.
CAUTION
I
R
R
I
T
AN
T
.
kc
ab
no
sn
oi
t
u
a
c
da
e
R
N
O
IT
N
ET
T
A
I
R
R
A
T
I
NT
.
s
rev
e
r
e
l
r
u
s
s
ec
ne
du
r
p
s
e
d
z
e
s
i
L
MONTHS
REPLACE
AIR FILTER INSTALLATION
Install the air filter behind the vented door on the rear wall of
the refrigerator compartment.
Pop the bubble on the back of the indicator to activate.
Place indicator in notches beneath the air filter (on some
models) or in visible area (models without notches).
A. Status indicator window
B. Air filter status indicator
C. Notches
D. Air filter
B
A
C D
ENERGY AND NORMAL OPERATING SOUNDS
Your new French Door Bottom Mount refrigerator has been
designed to optimize energy efficiency, and better regulate
temperatures to match cooling demand.
You may notice that it operates differently from your previously
owned refrigerator.
It is normal for the high-efficiency compressor to run for
extended periods of time at varying speeds in order to consume
only the energy necessary for optimum efficiency.
In addition, during various stages of the cooling cycle, you may
hear normal operating sounds that are unfamiliar to you.
Page view 0
1 2

Summary of Contents

Page 1 - GETTING STARTED

GETTING STARTEDSAVE THESE AND ALL INSTRUCTIONS! For more details and additional important information, see the other instructions provided inside your

Page 2 - POUR COMMENCER

W10325092D 12/14© 2014. Tous droits réservés. Imprimé aux É.-U.POUR COMMENCERCONSERVER CES INSTRUCTIONS ET TOUTES LES AUTRES ! Pour plus de détails et

Comments to this Manuals

No comments