Jason International, Inc. • 501.771.4477 Page 5 of 9 Customer Service : 800.255.5766
INSTALLATION INSTRUCTIONS (cont.)
cord. Connect the pump to a GFCI (Ground Fault Circuit
Interupter) with 240v (volt), 15A (amp), 60HZ (hertz) elec-
trical service with a service ground receptacle dedicated
for use by this bath.
6. Export Integrity Whirlpool Control Box (120v,50Hz):
This Whirlpool bath is provided with an Air On/Off switch.
The pump is pre-wired to a control box which has a 36”
cord. Connect the pump to a GFCI (Ground Fault Circuit
Interupter) with 120v (volt), 20A (amp), 50HZ (hertz) elec-
trical service with a service ground receptacle dedicated
for use by this bath.
7. Export Integrity Whirlpool Control Box (240v,50Hz):
This Whirlpool bath is provided with an Air On/Off switch.
The pump is pre-wired to a control box which has a 36”
cord. Connect the pump to a GFCI (Ground Fault Circuit
Interupter) with 240v (volt), 15A (amp), 50HZ (hertz) elec-
trical service with a service ground receptacle dedicated
for use by this bath.
DANGER: Do not alter the factory installed wiring.
All building materials and wiring should be routed away
from the pump or other heat-producing components of
the unit.
CLEANING
1. Remove all loose debris. Construction plaster or excess
grout can be removed with the use of a wood (edge)
trowel.
2. Paint or tar stains may need to be removed with a
cleaner such as paint thinner, turpentine, or isopropyl
alcohol (rubbing alcohol). Never allow the cleaner to
soak against the acrylic surface for long periods of time.
Always rinse the surface immediately following the
use of cleaners.
3. Follow the manufacturer’s instructions for safe use of
cleaning products. If the surface becomes scratched or
dulled, it may be restored by using a quality plastic polish,
like Novus Plastic Polish No. 2 (available from the Jason
Dealer). It is always preferable to protect the acrylic
surface during installation to minimize cleanup and
prevent surface damage.
WATER TESTING
Before finishing the installation, it is recommended that the
bath be water tested and the plumbing tested for leaks.
1. Before water testing the bath, make sure any pump
unions are hand tight. Do not over tighten or use a pipe
wrench. This will damage the unions and cause leaking.
If the unit leaks with the unions hand tight, then loosen
the unions(s) and check the O-ring seal to ensure it is
properly seated.
2. Fill and operate the bath. Close the drain and fill the
bath with water to at least 10 inches [25 cm] below the
bath deck. The inlet temperature should not exceed 104°F
(40°C) as this could damage the acrylic surface. Refer
to the FILLING AND DRAINING section of this owner’s
manual for more information.
NEVER RUN THE WHIRLPOOL PUMP WITHOUT
ENOUGH WATER IN THE BATH TO COVER THE
JETS.
3. Before starting the pump, direct the jet nozzles downward
to prevent the possibility of water splashing from the bath.
Refer to the OPERATING INSTRUCTIONS, FEATURES,
AND CONTROLS section of this Owner’s Manual.
4. Inspect the plumbing for leaks.
5. Turn the equipment Off and then drain the water. The
bath unit and its plumbing are designed to drain after each
use whether used as a whirlpool bath, air bath, soaking
bath, or when taking a shower.
(16 pages)
(56 pages)
(60 pages)
(48 pages)
(60 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals