Whirlpool AWE 9725 Instruction for Use download pdf (Page 13)

GB 13

What should I do when the automatic safety system detects a malfunction?

The programme is interrupted and various indicators (depending on model) point to the source of the fault.

Fault description table:

a. Water inlet fault (no or insufficient water supply)

The display alternately shows “FH”. Switch off the

appliance by turning the programme selector to

the “ ” position and unplug it.

Check whether:

•

the tap is fully turned on and the water supply

pressure is sufficient;

•

the water inlet hose is kinked;

•

the mesh filter in the water inlet hose is blocked

(see “Care and Maintenance”);

•

the water in the water inlet hose is frozen.

•

the appliance has a safety hose and the safety

valve is open (red indicator in the safety valve

inspection window).

In this case replace it with a new safety hose.

Reconnect the appliance.

Reselect the desired programme and press the

“Start/Pause”

button to continue with the

programme (do not add detergent for this programme).

If the fault re-occurs, contact the After-Sales (see

“After-Sales Service”)

b.Draining out fault

The display alternately shows “FP”. Switch the

appliance off by turning the programme selector to

the “ ” position and unplug it.

Check whether:

•

the drain hose is kinked (see “Installation”);

•

the pump impeller is obstructed (see “Cleaning

The Foreign Body Trap”).

•

the water in the drain hose is frozen.

•

if water has remained in the drum, you can drain

it by following the instructions in the chapter

“Draining Residual Water”.

IMPORTANT

: Before draining, allow the wash

water to cool down.

Reconnect the appliance.

Reselect the desired programme and press the

“Start/Pause”

button to continue with the

programme (do not add detergent for this programme).

If the fault re-occurs, contact After-Sales Service

(see “After-Sales Service”).

c. Electrical module fault

The display shows “F5” to “F15”.

Select a programme and press the

“Start/Pause”

button again.

If the fault re-occurs, contact After-Sales Service

(see “After-Sales Service”).

d.Water Stop fault

(depending on model)

The pump operates and the display shows “FA”.

Switch the appliance off by turning the programme

selector to the “ ” position, unplug the appliance

and turn off the water tap.

The “Water Stop” fault may have been

triggered by:

too much foam.

a leak in the inlet hose or in the appliance.

Tilt the appliance forwards carefully to allow the

water to drain out.

Then:

Reconnect the appliance,

turn on water supply (if

“Start/Pause”

button is not

pressed, but the machine begins to fill, turn off the

water supply tap and contact After-Sales Service),

reselect the desired programme and press the

“Start/Pause”

button.

If the fault occurs again, contact After-Sales

Service (see “After-Sales Service”).

e. Foam detection

The display shows “F4”; too much foam

interrupted the washing programme.

Press the

“Start/Pause”

button.

Move the programme selector to the “Drain”

programme.

Start this programme by pressing the

“Start/Pause”

button again.

After the “Drain” programme is finished, start

the original washing programme again, but avoid

excessive detergent dosing.

If your washing machine has an LCD-display,

Cancel the preselected programme by pressing

the “Reset” button.

After the “Drain” programme is finished, start

the original washing programme again, but avoid

excessive detergent dosing.

The display indicates: Fault description

FH “Water inlet fault”

FP “Draining fault”

F5 to F15 “Electrical components fault”

FA “Water stop fault”

F4 “Foam detection / Overdosing of detergent”

31210411GB.fm Page 13 Wednesday, May 25, 2005 7:00 PM

1 2 ... 8 9 10 11 12 13 14 15 16 17 18

Comments to this Manuals

No comments

Whirlpool AWE 9725 Instruction for Use Page 13

Comments to this Manuals

Related products and manuals for Washing machines Whirlpool AWE 9725