Whirlpool WT640 User Manual download pdf (Page 18)

Something Wrong? Troubleshooting

The machine wont start:

(Nothing lights up on the

control panel).

Lights/Display illuminate on

the control panel but the

washcycle will not start.

The machine fails to fill with

water.

The machine does not drain

or spin (during the first wash

cycle,after installation).

The machine does not drain

or spin (although it has

drained/spun during

previous wash cycles).

The programme takes a long

time.

There is too much foam in the

drum during the wash cycle.

Steam is coming from the

dispenser drawer.

 Check the appliance is fully plugged into the socket and switched on.

 Is the socket ok? Try another appliance in the socket to check.

 Is the fuse in the plug ok? If not, replace it, fuse must be 13 Amps (see Care and Maintenance ).

 There has been a power failure -Check another electrical device in your home to see if this is

the case.

 The ON/OFF button has not been pressed.

 The Start/Cancel button has not been pressed, for at least 3 seconds - Press and hold the

Start/Cancel button until the machine starts to operate.

 The appliance door is not shut properly -Close the door firmly and try the machine again.

 The Start/Cancel button has not been pressed, for at least 3 seconds -Press and hold the

Start/Cancel button until the machine starts to operate.

 The cold water supply tap is not turned on - (H2O is diplayed).

 Have you selected Time Delay (see Programmes and Option Modifiers)

 The Start/Cancel button has not been pressed,for at least 3 seconds - Press and hold the

Start/Cancel button until the machine starts to operate.

 Is the Prewash indicator light flashing? This indicates the machine has failed to take in

water (see Installation ) - Check that:

-The cold water inlet hose is connected to the tap.

-The hose is not kinked.

-The cold water supply tap is turned on...Ensure it is turned fully on.

-The water pressure is insufficient (see Technical Details Chart ).

-The inlet filter is not blocked...Turn off the water, unscrew the fill hose at the back of

the appliance then remove and clean the filter.

Note: Modern machines use less water and the water taken into the machine is

automatically adjusted depending on the load in the drum. For this reason, you may

not always be able to see water in the drum: But if the load is wet and the machine

completes the wash cycle then the amount of water into the machine is sufficient.

 Has the drain hose been installed correctly (see Installation ).

 Are the drain hose,standpipe or undersink connections blocked?

Note: If the drain hose is connected to an undersink U trap - Check that the sink

trap blanking plug was removed before the drain hose was connected. This is the most

common installation fault.

 Is the drain hose kinked or squashed -Check the hose at the back of the machine.

 Carry out the additional checks listed below...

 There has been an unbalanced load in the drum and the machine could not spin - Try the

machine again with a different wash oad (see Automatic Features ,Programmes and Option

modifiers ).

 Has the Rinse Hold option been selected? Rinse Hold indicator ight will flash.

-To complete the paused programme press either the Start/Cancel button or the

Rinse Hold button (see Programmes and Option modifiers ).

 If the machine completes the wash cycle, it is unlikely there is a problem.

 Check the programme table to be sure the programme you have selected is that most suited

for your needs -The table also gives an indication of approximate programme times you can

expect.

Note: The programme times listed in the Programme Table are approximate.

Options selected can affect the programme times (see Programmes and Option modifiers ).

The wash load, temperature and pressure of the incoming water supply can cause

some variation in the programme times.

 Check that the detergent you have used is suitable for Automatic machines.

 Refer to the detergent manufacturers recommendations to ensure that you have not used

too much detergent.

 If you have used the wrong type of detergent (or too much), select a Rinse programme to

flush out your machine.

 This is not a fault,we have designed the machine to release steam from the drawers during

hot washes.

If your machine seems not to be working GO through the following troubleshooting suggestion BEFORE you call your Service Centre

(see Service)

Section 1: All Ultima Models - General Troubleshooting

Problem:

Possible causes / Solution

1 2 ... 13 14 15 16 17 18 19 20

Comments to this Manuals

No comments

Whirlpool WT640 User Manual Page 18

Comments to this Manuals

Related products and manuals for Washing machines Whirlpool WT640