Whirlpool RS696PXE Service Manual

JOB AIDPart No. 4322212VISION II DROP-IN RANGEMODELS RS610PXE, RS675PXE, & RS696PXE

- 6 -3. From the back of the unit, grip the sides ofthe cooktop assembly, and separate itfrom the control panel. IMPORTANT RE-MOVAL INSTRUCTIONS: To a

- 7 -CERAN GLASS MODEL1. Remove the four screws from the supportplate at the rear of the cooktop and re-move the plate.Rear Cover(8) ScrewsControl Com

- 8 -4. From the back of the unit, grip the sides ofthe cooktop, lift it, then slide the cooktopback far enough to access the controlpanel.5. To remov

- 9 -1. To install the control panel, hook the sidesover the top of the side support, then raiseup on the air deflector and rotate thebottom of the co

- 10 -Refer to the illustration on the following page.REMOVING A SURFACE ELEMENT CONTROL1. Remove the cooktop (refer to page 4) so that you can access

- 11 -Ceran GlassTrim RingFrame ScrewHot Surface IndicatorRubberGrommetBacker PlateSupport BracketSupport BracketHeat ShieldHeat ShieldSurface Element

- 12 -OPEN COIL COOKTOP COMPONENTSUse the following procedure to access the cooktop components:1. Unplug the elements and then remove the drip pans.2.

- 13 -Refer to the illustration on the following page.REMOVING AN ELEMENT CONTROL1. Remove the knob and two mounting screws from the element control y

- 14 -Red LensSlide Arms On LightOver Shoulder Of LensTop Of Control PanelPress Arms Against Bottom Of PanelIndicator LightKnobInfinite SwitchInfinite

- 15 -WIRING DIAGRAMSModels RS610PXEW & RS610PXENL2NL1GNDBKBKVVVVORRBUBUBUBUBUBUOR/WRWL1PH1OR ORH2L2ELECTRONIC CONTROL - WP #4448874LFTRANSFORMERP

Copyright 1997 Whirlpool CorporationOBJECTIVEThe objective of this Job Aid is to have the experienced appliance technician becomefamiliar with the ope

- 16 -Models RS675PXEQ & RS675PXEZL2NL1GNDBKBKVVVVORRRBUOR/WRWLOCKUNLOCKL1PH1OR ORH2L2ELECTRONIC CONTROL - WP #4448874LFTRANSFORMERP5-2P3-8P5-1P2-

- 17 -Models RS696PXEB & RS696PXEQL2NL1GNDBKBKVVVVORRBUOR/WRWLOCKUNLOCKL1PH1OR ORH2L2ELECTRONIC CONTROL - WP #4448874LFTRANSFORMERP5-2P3-8P5-1P2-1

- 18 -STRIP CIRCUITSBAKE & PREHEAT - BAKEBKBKRRR/WOR/WOR/WORGYBAKE - 2000WBROIL - 3000WELECTRONIC OVEN CONTROLL1L2 NMW14P2-3BKP2-2P3-2P2-4P2-1P4-1

- 19 -CLEAN (ABOVE 600˚F) &PREHEAT - CLEAN (BELOW 600˚F)BKBKPNKYRWWRORTANTANYDOORSW 2DOOR LOCKSOLENOIDR/WOR/WPULSERELAYLOCK RELAYUNLOCK RELAYBAKE

- 20 -FAILURE CODES & REFERENCE DATAModels RS610PXEW & RS610PXENFAULT CODE ERROR CODEMEANING OFFAILURE CODEREPAIR PROCEDURE- F0 - All E-CodesD

- 21 -FAILURE CODES & REFERENCE DATAFAULT CODE ERROR CODEMEANING OFFAILURE CODEREPAIR PROCEDURE- F0 - All E-CodesDefault F-Codeno failure.Will onl

- 22 -TESTING THE COMPONENTSTEST PROCEDURERESULTSCOMPONENT COOKTOP HI LIMIT SURFACE ELEMENT1. Remove the element from theconnector.2. Set the ohmmet

- 23 - SINGLE TERMINAL (BARRED) BOTTOM SIDE OF ELEMENT SINGLE TERMINAL (OPEN) BOTTOM VIEW OF ELEMENT S

- 24 -2A 2B1A1B2A 2B1B1ATo test a limiter, perform the following steps:1. Use an ohmmeter and set the range to R x 1.2. With no power applied, touch t

- 25 -WhirlpoolPart No.Numberof TurnsWattage(Nom.)Voltage208/240ElementSizeHot Watts@ 240V –10% +5%Cold OhmsResistance660529 4 940 / 1250 208 / 240 6&

WARNING LABELSThis Job Aid is intended for factory-service technicians only. We recommend that customers DO NOTservice their own units, because of the

- 26 -Line voltage should be minimum240-volts. If necessary, electri-cian should repair cause for lowline voltage.Check wiring (see wiring dia-grams).

- 27 - PROBLEM SOLUTIONPOSSIBLE CAUSELine voltage should be minimum240-volts. Electrician should re-pair cause for low line voltage.Check element.Def

- 28 -WARRANTYWhirlpool® Drop-In RangeWHIRLPOOL WILL PAY FOR:FSP® replacement parts and repair labor to correct defects in mate-rials or workmanship.

Copyright 1997 Whirlpool Corporation, Benton Harbor, MIWHIRLPOOL CORPORATION assumes no responsibility forany repair made on our products by anyone ot

- 1 -Table of ContentsModel & Serial Number Location ...

- 2 -MODEL & SERIAL NUMBER LOCATIONThe Model/Serial Number Plate is located on the oven frame.Model/Serial Plate(On Oven Frame)

- 3 -COMPONENT LOCATIONSIndicator LightDoor Latch Mechanism(Solenoid & Door SwitchesOn Self-Clean Models)Broil ElementOven Temperature SensorBake

- 4 -CONTROL PANEL REMOVAL small end of pin here2. Remove the two screws from each sidetrim and remove them from the range.NOTE: Gently tilt

- 5 -OPEN COIL MODEL1. Remove the screws from the rear coverand remove it from the range.Do Not remove the control compartmentback and back cover.Rea