Whirlpool AKT 326/IX Instruction for Use download pdf (Page 3)

INSTALLATION

Recommendations

Important: Before any installation or maintenance

operation, disconnect the fryer from the mains power

supply.

• Electrical connections must be made before connecting

the appliance to the electricity supply.

• Installation must be performed by a qualified technician

according to the manufacturer's instructions and current

local regulations.

• After unpacking the fryer, check that there has been no

damage during transport. If in doubt, contact the nearest

dealer or Authorised After Sales Service.

Preparation of fitted cabinet

• Perform all required cuts on the work top before

inserting the appliance. Carefully remove all chips or

residue which could impair efficient operation of the

appliance.

• The fryer must be recessed in a work top with a thickness

of min. 30 and max. 50 mm.

• Insert a separator panel at a minimum distance of 20 mm

from the bottom of the fryer, so that it is not accessible to

the user.

• If the fryer is to be installed next to a column unit, leave a

distance of at least 100 mm from the fryer edge.

• Make an opening in the worktop, observing the

dimensions specified.

• Fit the seal supplied onto the hob (if not already present),

after carefully cleaning the application surface.

Important: before installing the fryer, remove any plastic

protection film applied.

Ensure that the opening made in the worktop to house the

fryer corresponds to the dimensional drawing specifications,

within the relative tolerances.

Never force the fryer into the worktop.

• For installation, use the relative brackets and screws

supplied.

1. Position the hob in the work top opening made respecting

the dimension indicated on first page.

NOTE: The power supply cable must be long enough to

permit its upward extraction.

2. To secure the hob, use the brackets (A) provided with it.

3. Fit the brackets into the relevant bores shown by the

arrow and fasten them by means of their screws in

accordance with the thickness of the work top (see fig. 1).

Electrical connection

• Regulations require that the appliance is earthed.

• The electrical connection must be made by a qualified

technician according to the manufacturer's instructions

and current local regulations.

• The installer is responsible for the correct electrical

connection of the appliance and the observance of the

relative safety standards.

• To comply with directives governing safety, during

installation use a single-pole switch with a minimum gap

between contacts of 3 mm.

• Do not use multiple plug adapters or extension leads.

• After installation, electrical parts must not be accessible.

Connection to the electrical mains

Note: the yellow/green earthing wire (B) must be

connected to the screw. If the power cable is not yet

connected:

• strip approx. 70 mm of sheath from the power supply

cable

• strip approx. 10 mm of sheath from the wires

• open the terminal board (C) by pressing the side tabs by

means of a suitable tool.

• insert the power cable (D) in clamp (E) and connect the

wires to the terminal board.

• close the terminal board cover.

• after the electrical connection, insert the hob from the

above and secure on the fixing brackets as shown in

figure 1.

Declaration of conformity

• This cooking hob has been designed, constructed and

marketed in compliance with:

- safety objectives of the “Low Voltage” Directive

2006/95/EC (which replaces 73/23/EEC and

subsequent amendments).

- protection requirements of EEC Directive “EMC”

2004/108.

- This cooktop is suitable for contact with foodstuffs and

complies with EEC (CE) Regulation n. 1935/2004.

PROTECTING THE ENVIRONMENT

Disposal of packaging

• The packaging material is entirely recyclable, and is

marked with the recycling symbol .

• Do not dispose of the various packaging materials

carelessly, but do so responsibly and in full compliance

with local authority regulations governing waste disposal.

Disposal of old household appliances

• This appliance is marked according to the European

directive 2002/96/EC on Waste Electrical and Electronic

Equipment (WEEE). By ensuring this product is disposed

of correctly, you will help prevent potential negative

consequences for the environment and human health.

The symbol on the product, or on the documents

accompanying the product, indicates that this appliance

may not be treated as household waste. Instead it shall be

handed over to the applicable collection point for the

recycling of electrical and electronic equipment. Dispose

of in accordance with local standards governing waste

disposal.

• For further information on the treatment, recovery and

recycling of this product, contact the relevant local

authority, household waste collection service, or the

outlet at which the product was purchased.

ASSEMBLY

After having cleaned the perimeter surface, apply the

supplied gasket to the hob as shown in the figure.

Fig. 1

Fig. 2

Fig. 3

1 2 3

Comments to this Manuals

No comments

Whirlpool AKT 326/IX Instruction for Use Page 3

Comments to this Manuals