(see at right for options description)
PROGRAMS SELECTION
BUTTON
Push “P” button (repeatedly)
until selected program number
is shown on the display
(P1...Px) - see “Table of
programs” below.
START/RESUME BUTTON
Push this button to start the selected program: the
indicator lights up and goes off at the end of the
program.
When the door is opened during a washing cycle,
the cycle is temporarily paused: the Start indicator
blinks. To resume the cycle push Start button and
close the door within 3 seconds.
CANCEL/OFF BUTTON
Push this button to switch off the control panel.
If pressed when a program is running it cancels the
program ongoing draining water for 1 minute
(0:01 is shown into the display).
If pressed when the dishwasher is switched off,
it drains any possible liquids from dishwasher
(1 minute process).
1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without any options) and may vary depending on
conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.
2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the
EN/Standard loading c
omparison test and other te
sts, contact the fol
lowing address: “contac
[email protected]”.
*Power consumption in Left-on mode: 1.27 W / Off-mode: 0.40 W
Table of programs
Deter-
gent
Consumption
Drying
Phase
Programs
Available
options
Loading instructions
Litres kWh
Minutes
1)
P1
Sensor 40°-70°C
Delay
1/2 load
PowerClean
®
Recommended program for routine
washes, with dried-on food.
X 7-15 1.00-1.70 70-172 Full
P2
Pre-Wash cold
Delay Crockery to be washed later. — 4.0 0.01 14-16 NO
P3
Rapid 45°C
Delay
Lightly soiled crockery, with no dried-
on food.
X 11.0 0.85 30-50 NO
P4
Eco
2)
50°C
Delay
1/2 load
PowerClean
®
Normally soiled crockery.
Standard program, the most efficient
in terms of its combined energy and
water consumption.
X 10.0 0.92 240 Full
P5
Daily 60°C
Delay
1/2 load
Normally to heavily soiled crockery. X 11.0 1.30 80-95 Full
P6
Steam
Delay
PowerClean
®
Program including steam action
dedicated for heavily soiled crockery,
pots and pans.
Soaking or hand pretreatment is no
longer needed.
X 14.5 1.75 180-190 Full
5019 300 02454
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS
QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
Options and display description
SALT INDICATOR
When lit (at the end of the cycle),
the salt reservoir needs to be
refilled.
RINSE AID INDICATOR
When lit (at the end of the cycle),
the rinse aid dispenser needs to
be refilled.
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY
BUTTON EXCEPT CANCEL/OFF BUTTON.
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES
AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.
TABLET SETTING
This setting allows to optimize
the cycle performances
according the type of
detergent used.
Push the Tablet button for
3 seconds (until the indicator
lights up) if you are using the
combined detergents in tablet
(rinse aid, salt and detergent in
1 dose). If you are using
powder detergent or gel
detergent, the Tablet indicator
on the control panel has to be
off.
DELAYED START BUTTON
Push the button (repeatedly)
to delay the start of the
program – delay indicator
turns on. Adjustable from 1
to 24 hours. With each press
of the button, the delay
increases by one hour and
after “h 24” returns to
“h 00”. When this option is
selected the delay indicator
turns on. Then press the
START button. The
dishwasher will start after the
set time.
WASH TIME DISPLAY
Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates
the time remaining until program start (h.00) - below 1h (0:min).
If “Fx Ey” messages appears on the display, see page 6 - chapter “What to do if...”.
POWERCLEAN
®
Thanks to the additional
power jets this option
provides a more intensive
and powerful wash in the
lower rack, in the specific
area. This option is
recommended for washing
pots and casseroles (see
page 4). Press this button to
activate PowerClean (the
indicator lights up).
1/2 LOAD BUTTON
Half load cycle can be used
for the upper or lower
rack.
Select the required
program then press the
“Half Load” button - the
light comes on.
Turns off at the end of the
program.
The “Half Load” option
can be used with the
programs indicated in the
table of programs.
Comments to this Manuals