Whirlpool ADG 9623 FD A++ Instruction for Use download pdf

EN -1-

Chart

(see at right for options description)

PROGRAM SELECTION

BUTTON

Push “P” button (repeatedly)

until selected program number

is shown on the display

(P1...Px) - see “Table of

programs” below.

START/RESUME BUTTON

Push this button to start the selected program: the

indicator lights up and goes off at the end of the program.

When the door is opened during a washing cycle, the

cycle is temporarily paused: the Start indicator blinks.

To resume the cycle push Start button and close

the door within 3 seconds.

CANCEL/OFF BUTTON

Push this button to switch off the control panel.

If pressed when a program is running it cancels the

program ongoing draining water for 1 minute

(0:01 is shown into the display).

If pressed when the dishwasher is switched off,

it drains any possible liquids from dishwasher

(1 minute process).

1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without any options) and may vary depending on

conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.

2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the

EN/Standard loading comparison test and other tests, contact the following address: “contact@whirlpool.com”.

* Power consumption in: Left-on mode: 0.70 W / Off-mode: 0.40 W.

Table of programs

Deter-

gent

Consumption

Drying

Phase

Programs

Available

options

Loading instructions

Litres kWh

Minutes

6th Sense

PowerClean

40-70°C

Delay

PowerClean

Use for normal soiled dishes with dried-

on food. Senses the level of soiling on the

dishes and adjusts the program

accordingly. When the sensor is detecting

the soil level an animation appears in the

display and the cycle duration is updated.

The PowerClean

option is activated

automatically with this program.

To deactivate, press the PowerClean

button on the control panel.

X 7-15 1.00-1.70 70-172 Full

Pre-Wash cold

Delay Crockery to be washed later.

— 4.0 0.01 14-16 NO

Fragile 40°C

Delay

Light soiling, for example glasses and

cups.

X 10.5 0.85 105-114 Light

Rapid 45°C

Delay

Lightly soiled crockery, with no

dried-on food.

X 11.0 0.85 30-50 NO

Eco

50°C

Delay

PowerClean

Normally soiled crockery.

Standard program the most efficient in

terms of its combined energy and water

consumption.

X 10.0 0.92 240 Full

Fast Daily 60°C

Delay Normally soiled crockery.

X 11.0 1.30 80-95 Full

Intensive 65°C

Delay

PowerClean

Recommended program for heavily soiled

crockery, especially suitable for pans and

saucepans.

X 15.0 1.60 165-175 Full

Hygiene

Delay

PowerClean

Normally or heavily soiled crockery, with

additional antibacterial wash.

Program interruption (e.g. due to door

opening) can compromise elimination of

germs.

X 14.0 1.40 110-120 Full

5019 300 02352

BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ

THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!

Options and display description

THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING

ANY BUTTON EXCEPT CANCEL/OFF BUTTON. FOR ENERGY SAVING

THE CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER

30 SECONDS IF NO CYCLE HAS STARTED.

TABLET SETTING

This setting allows to

optimize the cycle

performances according

the type of detergent

used.

Push the Tablet button

for 3 seconds (until the

indicator lights up) if you

are using the combined

detergents in tablet

(rinse aid, salt and

detergent in 1 dose).

If you are using powder

detergent or liquid

detergent, the Tablet

indicator on the control

panel has to be off.

DELAYED START

BUTTON

Push the button

(repeatedly) to delay the

start of the program.

Adjustable from 1 to

24 hours.

With each press of the

button, the delayed start

indicator increases by

one hour and after 24

restarts from 0.

Then press the START

button.

The dishwasher will

start after the set time.

POWERCLEAN

Thanks to the additional power jets

this option provides a more intensive

and powerful wash in the lower rack,

in the specific area.

This option is recommended for

washing pots and casseroles

(see page 4).

Press this button to activate

PowerClean

(the indicator lights

up). For non PowerClean

loading to

achieve best cleaning performances

and resources optimization,

PowerClean

should be switched

off.

WASH TIME DISPLAY

Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates

the time remaining until program start (h.00) - below 1h (0:min).

If “Fx Ey” messages appears on the display, see page 6 - chapter “What to do if...”.

SALT INDICATOR

When lit (at the end of the cycle), the

salt reservoir needs to be refilled.

RINSE AID INDICATOR

When lit (at the end of the cycle), the

rinse aid dispenser needs to be refilled.

OPERATION

INDICATOR

A LED light

projected on the

floor indicates that

the dishwasher is

working.

Quick reference guide

Whirlpool is a registered trademark of Whirlpool USA

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - 5019 300 02352

EN -1-Chart(see at right for options description)PROGRAM SELECTION BUTTONPush “P” button (repeatedly) until selected program number is shown on the di

Page 2 - Daily check

EN -2-First time use14109235 7861- salt reservoir2- rinse aid dispenser3- detergent dispenser4- racks system5,6,7,8- available functions on the pan

Page 3 - Daily use

EN -3-Daily check3Check the rinse aid indicator to check the level into the dispenser.(depending on the model)Rinse aid indicator on the control panel

Page 4 - How to use PowerClean

EN -4-How to load the racksCLICK!Rotate the flapclockwise andhook on rack4A - Adjustable flaps (2 or 4): in horizontal position for cups/long utensils

Page 5

EN -5-Switching off the appliance. Everything OK...Wash cycleSelect program678Maintenance and careMaintenance and careOverview of programsThe max. pos

Page 6 - What to do if

EN -6-What to do if...If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem.Most fault

Page 7

EN -7-What to do if...Crockery and cutlery... Possible causes... Solutions...have deposits: regeneration salt residue - Water too hard. - In areas

Page 8

EN -8-What to do if...If, after carrying out the above checks, the fault persists, disconnect the mains plug and turn off the water tap. Contact the A