GB
-1-
Chart
PROGRAM SELECTION
BUTTON
Push “Programs” button
(repeatedly) until the indicator
of the required program lights
up (see “Table of programs”
below).
START/RESUME BUTTON
Push this button to start the selected program: the
indicator lights up and goes off at the end of the
program. When the door is opened during a
washing cycle, the cycle is temporarely paused: the
Start indicator blinking. To restart the cycle close
the door and push Start button again.
CANCEL/OFF BUTTON
Push this button to switch off the control panel.
If pressed when a program is running it cancels the
program ongoing draining water for 1 minute.
If pressed when the dishwasher is switched off it
drains any possible liquids from dishwasher (1
minute process).
If the indicator flashes repeatedly, see page 6 -
chapter ”What to do if ...”.
(see at right for options description)
1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions
(without additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible
with sensor programs as a result of the appliance’s automatic calibration system.
2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for
detailed information on the EN/Standard loading comparison test and other tests, contact the following address:
Table of programs
Deter-
gent
Consumption
P
Programs
Available
options
Loading instructions
Litres kWh
Minutes
1)
1
AutoSensor 50-65°C
Delay
Half load
Recommended program for
routine washes, with dried-
on food (e.g. EN 50242).
X 7-14 1.00-1.60 70-155
2
Pre-Wash cold
Delay
Crockery to be washed
later.
— 4.0 0.03 14
3
Quickwash 45°C
Delay
Lightly soiled crockery, with
no dried-on food.
X 11.0 0.80 30
4
Eco
2)
50°C
Delay
Half load
Normally soiled crockery. X 12.0 1.05 150
5
Intensive 70°C
Delay
Recommended program for
heavily soiled crockery,
especially suitable for pans
and saucepans.
X 14.0 1.55 155
5019 396 01882
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ
THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING
ANY BUTTON EXCEPT CANCEL/OFF BUTTON.
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES
AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.
SALT INDICATOR
When lit (at the end of the
cycle), the salt reservoir
needs to be refilled.
HALF LOAD BUTTON
Half load cycle can be used
for the upper or lower rack.
Select the required program
then press the “Half Load”
button - the light comes on.
Turns off at the end of the
program. The “Half Load”
option can be used with the
programs indicated in the
table of programs.
TABLET SETTING
This setting allows to optimize the cycle performances
according the type of detergent used.
Push the Tablet button for 3 seconds (until the indicator
lights up) if you are using the combined detergents in
tablet (rinse aid, salt and deteregent in 1 dose).
If you are using powder detergent or liquid detergent,
the Tablet indicator on the control panel has to be off.
DELAYED START
BUTTON
The wash cycle can be
programmed to start
after 2, 4 or 8 hours.
Then press the Start
button. The wash
program will start after
the set time.
RINSE AID INDICATOR
When lit (at the end of the
cycle), the rinse aid
dispenser needs to be
refilled.
ADP 5555
Options and display description
Quick reference guide
Comments to this Manuals