Whirlpool DFP 58T1 C NX EU Instruction for Use download pdf (Page 13)

Care and maintenance

* Only available in selected models.

Shutting off the water and electricity

supplies

• Turn



off



the



water



tap



after



every



wash



cycle



avoid



leaks.

• Always

unplug



the



appliance



when

 cleaning



and



when



performing maintenance work.

Cleaning the dishwasher

• The



external

surfaces

of

the



machine



and



the



control

panel

can be cleaned using a non-abrasive cloth which has been

dampened with water. Do not use solvents or abrasive

products.

• Any



marks



the

insideof

the



appliance



may



removed



using a cloth dampened with water and a little vinegar.

Preventing unpleasant odours

• Always

keep



the



door



the

appliance



ajar



order

to

avoid



moisture from forming and being trapped inside the machine.

• Clean



the



seals



around



the

door

and



detergent



dispensers



regularly using a damp sponge. This will avoid food becoming

trapped in the seals, which is the main cause behind the

formation of unpleasant odours.

Cleaning the sprayer arms

Food residue may become encrusted onto the sprayer arms

and block the holes used to spray the water. It is therefore

recommended that you check the arms from time to time and

clean them with a small non-metallic brush.

The two sprayer arms may both be removed.

To remove the upper sprayer arm,

turn the plastic locking ring in an

anti-clockwise direction. The upper

sprayer arm should be replaced

so that the side with the greater

number of holes is facing upwards.

The lower sprayer arm can be

removed by pressing on the side

tabs and pulling it upwards.

Cleaning the water inlet filter*

If the water hoses are new or have not been used for an extended

period of time, let the water run to make sure it is clear and free

of impurities before performing the necessary connections. If this

precaution is not taken, the water inlet could become blocked

and damage the dishwasher.

Clean the water inlet filter at the tap outlet regularly.

- Turn off the water tap.

- Unscrew the end of the water inlet hose, remove the filter and

clean it carefully under running water.

- Re-place the filter and screw the water hose back into position.

Cleaning the filters

The filter assembly consists of three filters which remove food

residues from the washing water and then recirculate the water.

They should be cleaned if you wish to achieve the best results

in every wash.

Clean the filters regularly.

The dishwasher should not be used without filters or if the

filter is loose.

•Afterseveralwashes,checkthefilterassemblyandifnecessary

clean it thoroughly under running water, using a non-metallic

brush and following the instructions below:

1. Turn the cylindrical filter C in an anti-clockwise direction and

pull it out

(fig. 1).

2. Remove the cup filter B by exerting a slight pressure on the

side flaps

(fig. 2);

3. Slide out the stainless-steel plate filter A.

(fig. 3).

4. Inspect the trap and remove any food residues. NEVER

REMOVE the wash-cycle pump protection

(black detail) (fig.4).

After cleaning the filters, re-place the filter assembly and fix it in

position correctly; this is essential for maintaining the efficient

operation of the dishwasher.

Leaving the machine unused for extended

periods

• Disconnecttheappliancefromtheelectricitysupplyandshut

off the water tap.

• Leavethedooroftheapplianceajar.

• Whenyoureturn,runawashcyclewhenthedishwasheris

empty.

1 ... 12 13 14 ... 44

Comments to this Manuals

No comments

Whirlpool DFP 58T1 C NX EU Instruction for Use Page 13

Comments to this Manuals

Related products and manuals for Dishwashers Whirlpool DFP 58T1 C NX EU