Whirlpool IDE 750 UK.2 Instruction for Use Page 9

  • Download
  • Add to my manuals
  • Print
  • Page
    / 12
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 8
9
EN
Only use products that have been specifically designed
for dishwashers.
Do not use table salt or industrial salt.
If using a multi-functional product, it is not necessary to add
rinse aid; however, we recommend that you add salt,
especially if you live in an area where the water is hard or very
hard. If you do not add salt or rinse aid, the LOW SALT* and
LOW RINSE AID* indicator lights will flash continuously.
Loading the rinse aid
Rinse aid makes it easier for the crockery to dry, as water runs
off surfaces more readily and therefore does not leave streaks
or marks.
The rinse aid dispenser should be filled:
whenever the indicator light (H) signals that it is empty.
Illuminated light: add rinse aid; unlit light: there is no
shortage of rinse aid in the dispenser.
when the LOW RINSE AID* indicator light on the panel
flashes;
1. Open the dispenser by
turning the lid (G) in an
anticlockwise direction.
2. Pour in the rinse aid, making
sure it does not overflow from
the dispenser. If this happens,
clean the spill immediately with a
sponge.
3. Screw the lid back on.
NEVER pour the rinse aid
directly into the appliance tub.
Adjusting the amount of rinse aid
If you are not completely satisfied with the drying results, you
may adjust the quantity of rinse aid used. Use a screwdriver
to turn the dosage adjuster to one of the 6 pre-set positions
(the default position is set to 4):
if there are streaks on the crockery, set the adjuster to a
lower number (1-3).
if drops of water remain on the crockery or there are
limescale marks present after the cycle has finished, set the
adjuster to a higher number (4-6).
If you are using multi-functional tablets and you wish to
further improve the drying performance of the appliance, fill
the dispenser and set the dosage adjuster to 2.
Loading the refined salt
In order to obtain the best possible results from a wash cycle,
make sure that the dispenser is never empty. Refined salt
removes limescale from the water, thus avoiding the formation
of deposits on crockery. The salt dispenser is located in the
lower part of the dishwasher (
see Description
) and should be
filled:
when the green float* cannot be seen by simply looking at
the cap of the salt dispenser;
when the LOW SALT* indicator light on the panel flashes;
if your machine is not equipped with an indicator light or a
green float:
approximately every 30 wash cycles;
1. Remove the lower rack and
unscrew the cap of the dispenser (in
an anti-clockwise direction).
2. For the first wash cycle only: fill the
dispenser up to the edges with water.
3. Position the funnel provided
correctly (
see figure
) and fill the salt
dispenser up to the edges
(approximately 2 kg); it is normal for
a little water to leak out.
4. Remove the funnel, wipe away any salt residue from the
thread and screw the cap on tightly, so that detergent does
not leak into the dispenser during the wash cycle (this could
damage the water softening system beyond repair).
When salt has been added, run a wash cycle
immediately, without crockery, in order to remove any salt
solution that has leaked out and to avoid corrosion.
Adjusting the amount of salt*
It is possible to adjust the amount of salt used according to the
hardness of the water in your area (this information is available
from your local water board).
1. Unscrew the dispenser cap.
2. Turn the arrow on the neck of the
dispenser (
see figure
) towards the + or -
symbols, using the table below as a guide.
The default setting of the water softening system is +.
- If using multi-functional tablets, fill the salt dispenser and set
the adjuster to -; if the hardness of the water is greater than
60°fH, set it to +.
* Only available in selected models.
G
H
F
Rinse aid and refined salt
Page view 8
1 2 3 4 5 6 7 8 9 10 11 12

Comments to this Manuals

No comments