Whirlpool LFT 2284 A AG.R Instruction for Use download pdf (Page 28)

Electrical connection

Before inserting the plug into the electrical socket, make sure

that:

• The socket is earthed and complies with current regulations.

• The socket can withstand the maximum load of the appliance,

which is indicated on the data plate located on the inside of

the door

(see chapter entitled Description of the appliance).

• The power supply voltage falls within the values indicated on

the data plate on the inside of the door.

• The socket is compatible with the plug of the appliance. If

this is not the case, ask an authorised technician to replace

the plug

(see Assistance)

; do not use extension cables or

multiple sockets.

Once the appliance has been installed, the power supply

cable and the electrical socket should be easily accessible.

The cable should not be bent or compressed.

If the power supply cable is damaged, it must be replaced

by the manufacturer or its Technical Assistance Service in order

to prevent all potential hazards. (See “Assistance”)

The Company shall not be held responsible for any incidents

that occur if these regulations are not observed.

Anti-condensation strip*

After installing the dishwasher, open the door and stick the

adhesive transparent strip under the wooden shelf in order to

protect it from any condensation which may form.

Advice regarding the first wash cycle

After the appliance has been installed, immediately before

running the first wash cycle, completely fill the salt dispenser

with water and add only then approximately 1 kg of salt

(see

chapter entitled Rinse aid and refined salt)

. The water may

overflow: this is normal and is not a cause for concern. Select

the water hardness value

(see chapter entitled Rinse aid and

refined salt)

. After the salt has been poured into the machine,

the LOW SALT indicator light

* switches off.

If the salt container is not filled, the water softener and the

heating element may be damaged as a result.

Technical data

Dimensions

width 59.5 cm

height 82 cm

depth 57 cm

Capacity 14 standard place-settings

Water supply pressure

0,05 ÷ 1MPa (0.5 ÷ 10 bar)

7,25 – 145 psi

Power supply voltage See appliance data plate

Total absorbed power See appliance data plate

Fuse See appliance data plate

This dishwasher conforms

to the following European

Community Directives:

-2006/95/EC (Low Voltage)

-2004/108/EC (Electromagnetic

Compatibility)

-2009/125/EC (Comm. Reg.

1016/2010) (Ecodesign)

-97/17/EC (Labelling)

-2012/19/EC (WEEE)

ECODESIGN REGULATION

ECO wash cycle is the standard cycle to which the energy label data refers; this cycle can be used to wash crockery with a normal

soil level and is the most efficient in terms of energy and water consumption for this type of crockery. To reduce consumption even

further, only run the dishwasher when it is full.

Standby consumption: Left-on mode consumption: 4,5 W – Off mode consumption: 1,3 W

Consumption data table for the main cycles

* Cycle data refers to the values recorded in a laboratory, in accordance with European standard EN 50242.

** Data is obtained by recording values when the appliance is operational and loaded with user crockery.

Standard conditions* User conditions**

Energy consumption

(kWh/cycle)

Water consumption (l/cycle)

Duration

(min/cycle)

Energy consumption

(kWh/cycle)

Water consumption

(l/cycle)

Duration

(min/cycle)

INTENSIVE

1,50 15 150 1,30 14 135

NORMAL

1,20 15 120 1,05 14 110

1 ... 27 28 29 ... 48

Comments to this Manuals

No comments

Whirlpool LFT 2284 A AG.R Instruction for Use Page 28

Comments to this Manuals

Related products and manuals for Dishwashers Whirlpool LFT 2284 A AG.R