Whirlpool LL 43 S EU.C Instruction for Use download pdf (Page 17)

ARISTON DISHWASHER - Instructions for installation and use

1509)50-4

You have loaded your dishes and you now have

to set the wash cycle. It takes just one minute

to learn how

Starting the dishwasher

Ready, steady, go!

First of all.

Turn on the water tap com-

pletely and press ON-OFF

button "A". you will hear a

short beep and indicator light

"B" lights up. Now the appli-

ance is on and awaiting in-

structions.

Selecting the wash

cycle.

Select the wash cycle by

pressing button "P". Each

time you press the button, a

beep will sound and indica-

tor lights "E" will light up in

sequence: choose the cycle

you deem most suited to the

type of dishes to be washed

(take a look at page 17, where

you will find the wash cycle

table). If the appliance door

is shut, press the Start button

"R" and you will hear a beep;

the cycle will start up within

a few seconds.

The dishwasher informs

you.

Your dishwasher is fitted with

indicator lights (G) which

light up to indicate the cycle

phase under way.

Here are the symbols corre-

sponding to each cycle

phase:

pre-wash, wash, rinses, dry-

ing.

At all times, your dishwasher

tells you which cycle phase

is under way.

Modifying a wash

cycle in progress.

But if you have chosen the

wrong cycle, not to worry!

You can modify the wash cy-

cle in progress, if it has only

just started. Keep the RESET

button "R" pressed for about

5 seconds: a prolonged beep

will sound, followed by three

short beeps. Indicator light

"G" will turn off and at this

stage, all the settings will

have been cancelled. You are

now free to re-set the correct

wash cycle.

You've left out a dish?

Well, it happens to everyone.

Interrupt the wash cycle by

pressing the ON-OFF button,

insert the dish you had for-

gotten and press the ON-OFF

button again. The cycle will

start up from where you in-

terrupted it.

Finished?

The end of the wash cycle is

indicated by two short beeps

and the flashing of the dry-

ing phase indicator light.

• Turn off the water tap.

• Wait a few minutes before

unloading the dishes:

they are very hot! If you wait

a little while, they dry bet-

ter thanks to the steam.

• Empty the lower rack first.

You decide when it

starts.

When you have loaded the

dishes, you can choose when

to start your dishwasher be-

fore setting the wash cycle

desired. Press button "D" to

delay the start of the wash

cycle by 12, 9, 6 or 3 hours.

Each time you press it, you

will hear a short beep and the

indicator light "G" corre-

sponding to the selected de-

lay will light up.

Now you can select the de-

sired wash cycle. Press the

start button "R" and after you

hear the beep, the countdown

to the delayed start will be-

gin.

Once this time is up, the indi-

cator light will stop flashing

and the wash cycle will be-

gin.

If you have set a 12 hour

delay, for example, once you

have selected the wash

cycle, the 12 hour indicator

light will flash followed by

the others in sequence until

the set time delay is up. A

quick look at the indicator

lights will keep you informed

of the countdown progress at

all times.

Have you changed your

mind?

If you change your mind, you

can set a shorter time delay:

press button "D" to select it.

You need not reset the wash

cycle.

If on the other hand you want

to cancel the delay set and

you want the cycle to start

immediately, press button

"D" repeatedly until the cy-

cle starts and indicator light

"G" corresponding to the cy-

cle start phase comes on.

Dual function of

indicator lights "G"

1) flashing to indicate a

delayed start: to remind

you that you have set a de-

layed start;

2) on and not flashing be-

neath the cycle phase sym-

bol:

meaning the cycle has

started and is in the phase

indicated by the symbol.

Would you like to see

which settings you have

made?

At any time, when the cycle

is under way, if you press

button "P", the cycle in

progress indicator light will

light up for a few seconds.

Make sure the

wash cycle has

ended before

removing the

dishes!

Warning:

Turn the appliance off by

pressing button A,

unplug the appliance

from the electricity

socket to cut off the

power supply; the power

supply cable should

consequently be easily

accessible.

There's been a power

failure? Have you opened

the dishwasher door?

The wash cycle stops and

then restarts when the elec-

tricity comes back on or

when you shut the door. Eve-

rything is under control!

If opening the

door soon after

the end of the

programme,or

during it, stand

away from the

Dishwasher, to

avoid possible

injury from hot

steam.

1 ... 16 17 18 ... 80

Comments to this Manuals

No comments

Whirlpool LL 43 S EU.C Instruction for Use Page 17

Comments to this Manuals

Related products and manuals for Dishwashers Whirlpool LL 43 S EU.C