INSTALLATION INSTRUCTIONS UNDERCOUNTER DISHWASHERSTAINLESS STEEL TUB INSTRUCTIONS D'INSTALLATION LAVE-VAISSELLE SOUS COMPTOIRAVEC CUVE EN ACIER I
10IMPORTANT: The drain hose connection of the disposer or a waste tee must be made before the drain trap and at least 20" (50.8 cm) above the flo
11Option D, No waste disposer – with air gapPrepare DishwasherRemove and discard the foam blocks located above the front legs on each side of the dish
12Using two or more people, grasp sides of dishwasher door frame and place dishwasher on its back.Remove and discard the plastic rail cover on each si
13Make Power Supply Cord ConnectionOption A, Power Supply Cord:Route cord so that it does not touch dishwasher motor to lower part of dishwasher tub.
14Connect wires black to black and white to white, using UL Listed/CSA Approved twist-on wire connectors.If needed, see website for animated represent
15Built-up floors: If the kitchen floor is higher than the cabinet opening's floor - for example, the kitchen floor tile does not extend into the
16Push the plastic buttons out of the side of the tub.NOTE: Save the buttons to cover the holes after dishwasher is installed.Push bracket into slot o
17To adjust the door spring tension, unhook the spring from the rear leg of dishwasher.Using a ⁵⁄₁₆" nut driver or hex socket, remove the screw f
18Check that leveling legs are firmly against the floor. Close and latch the door, and place level against the front panel. Check that dishwasher is c
19Connect the ³⁄₈" compression fitting to the water supply line prior to installing the unit into the cabinet opening. Attach so that the ³⁄₄&quo
2TABLE OF CONTENTSDISHWASHER SAFETY... 2INSTALLATION REQUIREMENTS ...
20Make Direct Wire Electrical ConnectionNOTE: If the power supply cord was connected earlier, proceed to “Secure Dishwasher in Cabinet Opening” sectio
21Connect wires black to black and white to white, using ULListed/CSA Approved twist-on wire connectors (not included).If needed, see website for anim
22Secure dishwasher to countertopLocate brackets on top of dishwasher and secure dishwasher to countertop with two, #10 x ¹⁄₂" Phillips-head scre
23Complete InstallationPlace the plastic access panel against the dishwasher leg.Check that the lower edge of the access panel touches the floor. Adju
24Check Operation Read the Dishwasher User Instructions that came with your dishwasher. Check that all parts have been installed and no steps were s
25TABLE DES MATIÈRESSÉCURITÉ DU LAVE-VAISSELLE...25EXIGENCES D'INSTALLATION...
26EXIGENCES D'INSTALLATIONOutillage et piècesRassembler les outils et composants nécessaires avant d’entreprendre l’installation. Lire et observe
27Exigences d'emplacementUne source d'électricité avec liaison à la terre est nécessaire.Ne pas placer de canalisation d'évacuation, ca
28
29Exigences d’évacuation Un tuyau d'évacuation neuf est fourni avec le lave-vaisselle. Si ce tuyau n'est pas suffisamment long, utiliser un
3INSTALLATION REQUIREMENTSTools and PartsGather the recommended tools and parts before starting installation. Read and follow the instructions provide
30INSTRUCTIONS D'INSTALLATIONPréparation de l'ouverture d'encastrement du placard – Moyens de raccordement pré-existantsSi la canalisat
31Placard de bois : Poncer le trou jusqu'à obtenir une surface lisse.Placard métallique : Couvrir le trou avec l'œillet fourni dans la trous
32Fixer la canalisation d'alimentation en eau (tube de cuivre ou canalisation flexible à tresse d'acier) à la canalisation d'eau chaude
33IMPORTANT : Le raccordement du tuyau d'évacuation à la canalisation d'égout en T ou au raccord de broyeur à déchets doit être réalisé en a
34Option D - pas de broyeur à déchets – avec brise-siphonPréparation du lave-vaisselleEnlever et jeter les cales en polystyrène situées au-dessus des
35Faire intervenir deux personnes ou plus – saisir les côtés du châssis de la porte du lave-vaisselle pour placer le lave-vaisselle en appui sur la fa
36Raccordement du cordon d'alimentationOption A, cordon d’alimentation :Acheminer le cordon d'alimentation de façon à ce qu'il ne touch
37Connecter le conducteur noir avec le noir et le conducteur blanc avec le blanc à l'aide des connecteurs de fils (homologation UL ou CSA).Au bes
38Planchers surélevés : Si la hauteur du plancher de la cuisine est supérieure à celle de l'ouverture d'encastrement du placard. Par exemple
39Pousser sur les boutons en plastique pour les extraire du côté de la cuve.REMARQUE : Conserver les boutons à part pour recouvrir les trous une fois
4Location RequirementsGrounded electrical supply required.Do not run drain lines, water lines or electrical wiring where they can interfere with or co
40Alors qu'une autre personne retient l'appareil pour l'empêcher de basculer, ouvrir et refermer la porte plusieurs fois. Si la porte s
41Vérifier que chaque pied de réglage de l'aplomb est fermement en appui sur le sol. Fermer et verrouiller la porte; placer un niveau contre le p
42Raccorder le raccord de compression de ³⁄₈" à la canalisation d'alimentation en eau avant d'installer l'appareil dans l'ouv
43Raccordement électrique directREMARQUE : Si le cordon d'alimentation a été raccordé précédemment, passer à la section “Fixation du lave-vaissel
44Connecter le conducteur noir avec le noir et le conducteur blanc avec le blanc à l'aide des connecteurs de fils (homologation UL ou CSA) (non f
45Fixation du lave-vaisselle au plan de travailLocaliser les brides sur le dessus du lave-vaisselle et fixer celui-ci au plan de travail à l'aide
46Achever l'installationPlacer le panneau d’accès en plastique contre le pied du lave-vaisselle.Vérifier que la rive inférieure du panneau d’accè
47Contrôle du fonctionnement Lire les instructions d'utilisation du lave-vaisselle fournies avec le lave-vaisselle. Vérifier que toutes les piè
W10401504B© 2012.All rights reserved.Tous droits réservés.6/12Printed in U.S.A.Imprimé aux É.-U.
5
6Drain Requirements A new drain hose is supplied with your dishwasher. If drain hose is not long enough, use a new drain hose with a maximum length o
7INSTALLATION INSTRUCTIONSPrepare Cabinet Opening—Existing UtilitiesIf the water line and the cable extend to the locations shown, proceed to the “Ins
8Wood cabinet: Sand the hole until smooth.Metal cabinet: Cover hole with grommet included with power supply cord kit.Option B, Direct Wire:Helpful Tip
9Attach the water supply line (copper tubing or flexible braided line) to the hot water line using a connection configuration that is in compliance wi
Comments to this Manuals