Whirlpool duet 8578185 User Manual

ELECTRONICELECTRIC DRYERUse & Care GuideFor questions about features, operation/performance, parts, accessories or service, call: 1-800-253-1301or

101. Remove center silver-colored terminal block screw.2. Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire

113. Connect ground wire (green or bare) of direct wire cable to external ground conductor screw. Tighten screw.4. Place the hooked ends of the other

121. Loosen or remove center silver-colored terminal block screw.2. Place the hooked end of the neutral wire (white or center wire) of direct wire cab

13Venting RequirementsWARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS.IMPORTANT: Observe all governing codes and ordinances

14The angled hood style (shown here) is acceptable. An exhaust hood should cap the vent to keep rodents and insects from entering the home. Exhaust

15 Periscope Installation (For use with dryer vent to wall vent mismatch):Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm) mismatchPart N

16Install Leveling Legs1. To protect the floor, use a large flat piece of cardboard from the dryer carton. Place cardboard under the entire back edge

17DRYER USEStarting Your DryerWARNING: To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before

18 Press the WRINKLE SHIELD™ feature button if this option is desired. Press the END OF CYCLE SIGNAL button to set signal volume to desired level.

19Cycle tips Dry most loads using the preset cycle settings. Refer to the Automatic or Manual Preset Cycle Settings chart (in the “Cycles” section)

2TABLE OF CONTENTSDRYER SAFETY...3INSTALLATION INSTRUCTIONS...

20Automatic Preset Cycle Settings*Estimated Time with Dryness Level (medium) setting. Time will vary depending on load type and load size.Manual Cycle

21End of Cycle Signal The End of Cycle Signal produces an audible sound when the drying cycle is finished. Promptly removing clothes at the end of the

22DRYER CARECleaning the Dryer LocationKeep dryer area clear and free from items that would obstruct the flow of combustion and ventilation air.Cleani

23Vacation and Moving CareVacation careOperate your dryer only when you are at home. If you will be on vacation or not using your dryer for an extende

24TROUBLESHOOTINGFirst try the solutions suggested here and possibly avoid the cost of a service call...Dryer OperationDryer will not run Has a house

25 Is the dryer located in a room with temperature below45ºF (7ºC)? Proper operation of dryer cycles requires temperatures above 45ºF (7ºC). Is the

26ASSISTANCE OR SERVICEBefore calling for assistance or service, please check “Troubleshooting.” It may save you the cost of a service call. If you st

27Notes

WHIRLPOOL CORPORATION MAJOR APPLIANCE WARRANTYONE YEAR LIMITED WARRANTYFor one year from the date of purchase, when this major appliance is operated a

3DRYER SAFETYYou can be killed or seriously injured if you don't immediately You can be killed or seriously injured if you don'tfollow All

4INSTALLATION INSTRUCTIONSTools and PartsGather the required tools and parts before starting installation. Read and follow the safety instructions pro

5Location RequirementsYou will need A location that allows for proper exhaust installation. See “Venting Requirements.” A separate 30-amp circuit.

6Recessed or closet installation - Dryer on pedestal*Additional spacing recommended**Side or bottom venting - additional spacing recommendedMinimum in

7Electrical RequirementsIt is your responsibility To contact a qualified electrical installer. To be sure that the electrical connection is adequate

8Electrical ConnectionPower Supply Cord Direct Wire1. Disconnect power.2. Remove the hold-down screw and terminal block cover. 3. Install strain reli

9 Put power supply cord through the strain relief. Be sure that the wire insulation on the power supply cord is inside the strain relief. The strain