Whirlpool ET16JM User Manual download pdf (Page 6)

Adjusting the shelves.. .

I, First, remove food from shelf.

2. Slide shelf straight out to stop.

3. Lift front.

4. Slide the rest of the way out.

Replacing Shelf:

I. Fit back of shelf on top of guides

on the bottom of guides.

2. Lift front, slide shelf In until it clears

with wire stops

guide stops.

Shelf Guide

Removing crispers and crisper cover.. .

Removlng the Crispers:

Lilt the Front, Then the Back.

1. Slide crisper straiaht out to stop, lift front, then slide I

I II If I

the rest of the wai out.

2. Replace in the reverse order.

Removing Cover:

1. Lift front and remove the cover support.

2. Lift out cover by pulling up and out.

Replacing Cover:

I, Fit back of cover into notch supports on walls of

refrigerator, then lower front into place.

2. Replace cover support with the long tab towards

the front.

Note:

If support needs adjustment, turn

base right to raise, or left to lower.

Changing the light bulb...

WARNING: Before removlng the light bulb, either

unplug the refrlfjeratoror dlrconnect

the electricity leading to the re-

frigerator at the main power supply.

Shock and injury can occur if elec-

tricity remains connected.

Automatic ice maker.. .

Raise Slgnal

Arm to Stop Ice Maker.

lower Slgnal

Arm to Start It.

If you have Model ET16JM and have the automatic

ice maker accessory, or if you have Model ET16JK and

plan to add one later [Part No. ECKMF-83). there are a

few things you will want to know:

The ON/OFF lever is a wire signal arm.

Down...for making ice automatically;

Up,, .to shut off the ice maker.

Shake the bin occasionally to keep cubes sepa-

rated, and to obtain increased storage capacity.

It is normal for ice crescents to be attached by a

corner. They will break apart easily.

Ycu WIII hear water running when ice maker IS

working. You’ll hear ice fall into the bin Don’t let

these sounds bother you.

The ice maker will not operate until the freezer is

cold enough to make ice. This can take overnight.

‘ull out to stop.

me Front and Pull Again.

Unplug Ke

refrigerator first.

1. Reach behind control console to find bulb.

2. Remove bulb.

3. Replace with a 40.watt appliance bulb.

a-Bm*l~~w IKSS Guwm m---IR-

Because of new plumbing connections, the first

ice may be discolored cr off-flavored. Discard the

first few batches of ice.

If ice is not being made fast enough and more ice

is needed, turn the Refrigerator Control toward a

higher number. Wait a day and. if necessary, turn

the Freezer Control toward A.

If you remove the ice bin, raise the signal arm to

shut off the ice maker. When you return the bin,

push it all the way in and lower the arm to the ON

position.

If cubes are stored too long, they may develop an

off-flavor...like stale water. Throw them away. They

will be replaced. Cubes in the ice bin can also

become smaller by evaporation.

Good water quality is important for good ice quality

It is not recommended that the ice maker be con-

nected to a softened water supply Water softener

chemicals such as salt from a malfunctioning soft-

ener can damage the ice maker mold and lead to

poor quality ice. If a softened water supply cannot

be avoided, then it is important that the water soft-

ener be well maintained and operating properly.

1 2 3 4 5 6 7 8 9 10 11 12

Comments to this Manuals

No comments

Whirlpool ET16JM User Manual Page 6

Comments to this Manuals

Related products and manuals for Fridges Whirlpool ET16JM