Whirlpool Refrigerator ET1FHTXMB01 User Manual download pdf (Page 10)

Crisper Humidity Control

(on some models)

You can control the amount of humidity in the moisture-sealed

crisper. Adjust the control to any setting between LOW and HIGH.

LOW (open) for best storage of fruits and vegetables with skins.

HIGH (closed) for best storage of fresh, leafy vegetables.

Ice Maker

Turning the Ice Maker On/Off

To turn the ice maker ON, simply lower the wire shutoff arm.

To manually turn the ice maker OFF, lift the wire shutoff arm to the

OFF (arm up) position and listen for the click.

NOTE: Your ice maker has an automatic shutoff. As ice is made,

the ice cubes will fill the ice storage bin and the ice cubes will

raise the wire shutoff arm to the OFF (arm up) position. Do not

force the wire shutoff arm up or down.

Ice Production Rate

■ Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

■ The ice maker should produce approximately 8 to 12 batches

of ice in a 24-hour period.

■ To increase ice production, lower the freezer and refrigerator

temperature. See “Using the Controls.” Wait 24 hours

between adjustments.

■ For maximum ice production (on some models), push the

switch to ICE PLUS. The ice maker should produce 16 to

20 batches of ice in a 24-hour period in the Ice Plus mode.

Remember

■ The quality of your ice will be only as good as the quality of the

water supplied to your ice maker. Avoid connecting the ice

maker to a softened water supply. Water softener chemicals

(such as salt) can damage parts of the ice maker and lead to

poor quality ice. If a softened water supply cannot be avoided,

make sure the water softener is operating properly and is well

maintained.

■ Do not use anything sharp to break up the ice in the bin. This

can cause damage to the ice container and the dispenser

mechanism.

■ Do not store anything on top of or in the ice maker or ice bin.

Water Dispenser

IMPORTANT:

■ After connecting the refrigerator to a water source, flush the

water system by dispensing water into a sturdy container until

you draw and discard 2 to 3 gal. (8 to 12 L) of water, or for

approximately 5 minutes after the water begins dispensing.

The flushing process cleans the water system and clears the

air from the lines. As the air is cleared from the lines, water

may spurt out of the dispenser.

■ Allow several hours for the refrigerator to cool down and chill

water.

■ Dispense enough water every week to maintain a fresh supply.

To Dispense Water:

There are two water dispenser buttons for use with different sizes

of containers.

1. Press a sturdy glass against the back button or hold a

container under the dispenser while pressing the front button.

2. Remove the glass or release the front button to stop

dispensing.

Water Filtration System

NOTE: Do not use with water that is microbiologically unsafe

or of unknown quality without adequate disinfection before or

after the system. Systems certified for cyst reduction may be

used on disinfected waters that may contain filterable cysts.

Water Filter Status Light (on some models)

The water filter status light will help you know when to change

your water filter. The light will change from green to yellow. This

tells you that it is almost time to change the filter. It is

recommended that you replace the water filter when the status

light changes to red OR water flow to your water dispenser or ice

maker decreases noticeably.

After changing the water filter, reset the water filter status light.

The status light will change from red to green when the system is

reset.

Non-indicator Water Filter (on some models)

If your refrigerator does not have the status light, you should

change the water filter every 6 months depending upon your

usage. If the water flow to the water dispenser or ice maker

decreases noticeably before 6 months have passed, replace the

water filter more often.

Using the Dispenser Without the Water Filter

You can run the dispenser without a water filter. Your water will not

be filtered.

1. Remove the water filter.

2. Slide the cap off the end of the filter and replace the cap in the

base grille.

Cut Hazard

Use a sturdy glass when dispensing ice or water.

Failure to do so can result in cuts.

WARNING

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 47 48

Comments to this Manuals

No comments

Whirlpool Refrigerator ET1FHTXMB01 User Manual Page 10

Comments to this Manuals

Related products and manuals for Fridges Whirlpool Refrigerator ET1FHTXMB01