Whirlpool WHCF-DUF User Manual download pdf (Page 2)

Model

WHCF-DUF

Filter Replacement:

The contaminants or other substances removed or reduced by

this water filter are not necessarily in all users’ water.

Filter life varies depending on local water conditions and the vol-

ume of water used. We recommend that you change your filter

every 6 months. However, it can be replaced earlier if there is a

drop in pressure at the faucet.

To reduce Chlorine Taste and Odor,

use Replacement Filter: WHCF-GAC

Do not use with water that is microbiologically unsafe or of unknown quali-

ty without adequate disinfection before or after the system.

Systems certified for Cyst reduction may be used on disinfected water

that may contain filterable cysts. EPA Establishment #070595-CT-001

Filter Cartridge Replacement Instructions:

NOTE: Before changing cartridge, turn off incoming water

supply. Place a bucket under filter to catch the small amount

of water that will run out after housing removal.

1. Shut off water.

2. Relieve pressure in housing by pushing red vent button.

3. Unscrew housing and remove old cartridge. Wash housing

thoroughly with mild soap and water.

4. Insert new cartridge and re-install housing. Be sure cartridge is

seated in the housing before tightening onto head.

5. Use filter wrench to fully seat the cartridge. Tighten to make a

water tight seal.

6. Turn on water. If any leaks appear, tighten housing as needed.

7. Flush system for five (5) minutes.

Troubleshooting Guide

Water Leaks at Threaded Fittings:

Tighten slightly more until leak stops.

Water leaks at Push-in Connections

Push tubing in as far as it will go. If leaking continues, shut off

water at the original valve and remove water line by pushing in on

the connector collar while pulling the tubing away. (See Push-in

Fittings Section) Inspect tubing for cracks and scratches. If tubing

is cracked or scratched, simply cut that portion away and reinsert

tubing into fitting.

Make sure tubing is cut straight. If not, recut.

Help Line 1-866-245-9474

Monday Through Friday

8:00 a.m. to 9:00 p.m. EST

or write us at

Whirlpool Water Products

PO Box 765

Meriden, CT 06450

INSTR7016 1203 04/04

8562175 Whirlpool Water Products

Meriden, CT 06450

UNDER SINK MAIN FAUCET

FILTRATION

Standard System

Installation, Use & Care Guide

8562175/INSTR7016 1203

® Registered trademark/TM Trademark of Whirlpool, USA,

used under license.

TEFLON is a registered trademark of E.I. Dupont

® Marca registrada/TM Marca de comercio de Whirlpool, USA,

usado bajo licencia.

TEFLON es una marca registrada de E.I. Dupont

1 Year Limited Warranty

CUNO Incorporated warrants the original purchaser-consumer of its Product

that is free of defects in materials and workmanship. Any defect, malfunction, or

other failure of the Product to conform to this warranty will be remedied by

Warrantor in the manner provided below.

This Warranty, together with any warranties implied by law, shall be limited to a

duration of one (1) year from the original date of purchase by the consumer.

This Warranty does not apply to defects that result from abuse, misuse, alter-

ation or damage not caused by CUNO Incorporated.

THIS WARRANTY DOES NOT COVER, AND IS INTENDED TO EXCLUDE ANY

LIABILITY ON THE PART OF WARRANTOR, WHETHER UNDER THIS WAR-

RANTY OR UNDER ANY WARRANTY IMPLIED BY LAW, FOR ANY INDIRECT

OR CONSEQUENTIAL DAMAGES FOR BREACH HEREOF OR THEREOF.

Note: Some states prohibit limitations on the duration of implied warranties and

on the exclusion of indirect or consequential damages; and so the limitation on

implied warranties and on incidental and consequential damages may not be

applicable to you.

RESPONSIBILITY OF WARRANTOR

CUNO Incorporated’s responsibility under this warranty shall be to repair at its

expense, at no charge to the original purchaser-consumer any product that is

actually defective, malfunctioning or otherwise in violation of this warranty. If

CUNO Incorporated for any reason cannot repair a Product covered hereby

within two (2) weeks after receipt of the original purchaser-consumer’s notifica-

tion of a Warranty claim and the Product, then CUNO Incorporated’s responsi-

bility shall be, at its option, either to replace the defective Product with a compa-

rable new unit at no charge to the consumer or to refund the full purchase price.

CUNO Incorporated’s obligations of repair, replacement, or refund are condi-

tioned upon the return of the defective product to CUNO Incorporated.

If any Product hereby is actually defective within the terms of this Warranty, then

CUNO Incorporated will bear all the reasonable and proper shipping and mail-

ing charges actually incurred in the consumer’s return of the Product set forth

herein. If the Product proves not to be defective within the terms of this

Warranty, then all costs and expenses in connection with the processing of the

consumer’s claim hereunder shall be borne by the consumer.

RESPONSIBILITY OF THE CONSUMER

The original purchaser-consumer’s sole responsibility in the instance of a war-

ranty claim shall be to notify CUNO Incorporated of the defect, malfunction or

other manner in which the terms of this Warranty are violated.You may secure

performance or obligations hereunder by (in writing):

1. Identifying the Product involved (by model or serial number or other sufficient

description that will allow Warrantor to determine which product is defective).

2. Specifying where, when and from whom the Product was purchased.

3. Describing the nature of the defect, malfunction or other violation of this

Warranty.

4. Return the Product, with the above information to:

CUNO Incorporated, 400 Research Parkway, Meriden, CT 06450, U.S.A.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY

ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE.

To Release Tubing

Push in grey

collet to release

tubing. With collet

held, pull tubing

straight out.

To Attach Tubing

Push tubing in as far as

it will go. Tubing must be

inserted past o-ring and

hit backstop. Pull tube

to ensure it is secured.

Collet

Backstop

“Using Push-In Fittings”

6. Wrap Teflon

tape (2 1/2

wraps) around the 3/8” fit-

ting in a clockwise direction

and fasten to filter head

(see Figure 5). Do not use

pipe sealant (dope), as sol-

vents in some types of pipe

dope may cause damage to

plastic fittings.

7. Insert water supply line to

port marked "IN" (see

Figure 6, A) and insert

faucet line to port marked

"OUT" (see Figure 6, B).

Referring to section “Using

Push-in Fittings,” insert

plastic tubing into fittings,

making sure end of tubing

is firmly seated to backstop.

8. Fasten bracket to filter head with

four Phillips head screws provided.

(See Figure 7.) Fasten bracket to wall

with four Phillips head screws provid-

ed. If pre-drilling holes, bracket may

be used as a template for making

screw hole locations.

9. Lubricate housing o-ring with water.

10. Place filter into housing.

(See Figure 8.)

Align housing to filter head and screw

onto filter head. Tighten with wrench to

seal.

11. Slowly turn water supply on while depressing red air

release button on filter head and check for leaks. Then run

water for 5 minutes with an open faucet to flush out air.

3/8" Compression

Hex Nut

3/8" Ferrule

3/8" Tube Insert

3/8" x 1/2"

Faucet Adapter

Installation Instructions

For Use With Cold Water Only

NOTE: Remove items from under the sink. Place a catch basin

there to collect small amounts of water that may run out when dis-

connecting water supply lines.

1. Turn off cold water supply valve and remove existing fitting and/or

tubing from cold water side of faucet.

2. Loosely assemble sump to filter head and attach filter bracket.

Use this assembly to mark a location under the sink that is not in

the way but allows for easy access to change filter. Allow room to

operate housing wrench and a minimum of 2 1/2” clear space below

the unit to facilitate changing cartridge. Once this is done disassem-

ble components for installation.

3. Determine length of tubing required from filter

head/bracket to faucet and from water supply line

to filter head/bracket by holding tubing in place

ensuring it is of appropriate length. Do not kink

tubing as this will impede water flow. If necessary,

loop tubing around to avoid it being kinked.

Cut tubing straight with a utility knife or tube cut-

ter (for copper piping). (See Figure 1.)

4. Install faucet adapter fitting to faucet (see

Figure 2). Do not overtighten to prevent dam-

age to fitting. Referring to section “Using

Push-In Fittings”, insert a section of plastic

tubing into fitting, making sure end of tubing is

firmly seated to backstop.

5. Onto one end of the remaining sec-

tion of tubing, slide the compression

hex nut and ferrule onto the tubing and

put in the tube insert (see Figure 3).

Fasten this assembly onto 3/8” water

supply outlet. Do not overtighten (see

Figure 4). Overtightening will cause

tubing to separate from fitting.

Red Air

Release Button

Inlet Outlet

1. Filter Head

2. Filter Head Bracket

and eight Phillips

head screws

3. Housing Wrench

4. Filter Cartridge

5. Opaque Housing

6. 5’ of 3/8” Tubing

7. 3/8” Fitting x 1/2”

Faucet Adapter

8. 3/8” Compression

Hex Nut

9. 3/8” Ferrule

10. 3/8” Tube Insert

11. Two 3/8” x 3/8”

Push-In Fittings

Parts and Material Included:

Kit contains components necessary to connect 3/8” outlet tube to 1/2”

faucet fitting and 3/8” water supply. If you have any other size faucet

connection, you may need other parts for installation as required.

This filter can be used at any sink where water is used for drinking.

Figure 1

Figure 3

Correct

Incorrect

Figure 4

Figure 5

Figure 6

Figure 7

Figure 8

Gather the required tools before starting installation. Read and fol-

low the instructions provided with any tools listed here.

Tools and Parts Needed:

• Phillips Head Screwdriver

• Adjustable Wrench

• Teflon

Tape

• Utility Knife or Tube Cutter for

copper piping

Installation Requirements:

• Properly tighten all fittings to ensure a leak-free assembly.

• Install in a location that is not susceptible to freezing temperatures

as damage to the housing could occur.

• Install away from direct sunlight as prolonged exposure to light

can weaken plastic components.

• Some local codes may require the use of a licensed plumber or

certified installer when disrupting a potable water line. Determine

and follow any and all local codes and requirements.

• Allow room to operate housing wrench and a minimum of 2 1/2”

clear space below the unit to facilitate changing of the filter.

Figure 2

1 2 3 4

WHCF-DUF 1

Comments to this Manuals

No comments

Whirlpool WHCF-DUF User Manual Page 2

Comments to this Manuals

Related products and manuals for Sanitary ware Whirlpool WHCF-DUF