Whirlpool KRSC 9060 Instruction for Use download pdf (Page 17)

Ice Mode

The function is activated when the symbol is lit.

Press the ice mode button to select the symbol

corresponding to the type of ice required (cubes or

crushed); the symbol will light up.

Note: If the freezer compartment door is open,

make sure the lever located inside is not blocked,

since it prevents the transfer of ice from the

automatic ice-maker to the container installed in

the door.

Normal ice production should be about 7 to 8

batches of ice in a 24-hour period.

To dispense ice:

1. press the ice mode button and select the

required type of ice.

2. press a rigid glass against the ice dispenser lever.

Hold the glass close to the dispenser opening so

that ice does not fall outside of the glass

3. press lightly on the lever to activate the ice

dispenser. Pressing hard will not result in faster

dispensing or greater quantities

4. to stop dispensing, remove the glass slowly so

that ice does not fall outside the glass

5. do not use fragile glasses to dispense ice.

Water dispensing

When the ice and water dispenser is used for the

first time, the first ice cubes and water coming out

of the dispenser may have an unpleasant taste and

should therefore be discarded. It is advisable to

repeat the operation also when the dispenser has

not been used for some time.

To dispense water press a glass against the water

dispenser lever, removing the glass to stop

dispensing; at the same time the light inside the

dispenser comes on, and goes off when the lever is

released.

It is not necessary to press hard on the levers to

activate the dispenser. Pressing hard will not result

in faster dispensing or greater quantities.

Wait a few seconds before removing the glass, in

order to catch the last few drops of water or

pieces of ice.

The water and ice dispenser will not work when

the freezer compartment door is open.

The ice comes from the automatic ice-maker

container in the freezer compartment.

Using the ice and water dispenser

Advice on using the automatic ice-maker

If the freezer compartment door is open, make

sure to keep the inside flap free, since it serves as a

sensor for stopping the transfer of ice from the

automatic ice-maker, to the bucket located in the

inner door.

To remove and refit the ice bucket:

1. insert four fingers in the opening at the bottom

of the bucket and place your thumb on the

release button

2. holding the base of the bucket with both hands,

press the release button and lift the bucket up

and out. It is not necessary to turn the

automatic ice-maker control to the OFF

position: the automatic ice-maker will not

produce ice if the bucket is not installed in the

door.

3. Normal automatic ice production consists of

about 7 to 9 batches of ice cubes in a 24-hour

period.

IMPORTANT:

• Large amounts of ice cubes should be taken

directly from the bucket, and not from the

dispenser

• When selecting crushed ice, the cubes are

crushed just before being dispensed, therefore

the crushed ice may come out with a slight

delay. Noise from the ice crusher is normal, and

pieces of ice may vary in size. When changing

from crushed ice to ice cubes, a small amount

of crushed ice may come out together with the

first cubes.After switching on the refrigerator, it

usually takes overnight for the first ice cubes to

form.

• When using the water dispenser, keep the rim

of the glass near. Move the glass slowly to

prevent the water from spilling.

Using the automatic ice-maker

5019_715_02010_GB_IFU_SbS.qxp 12-03-2007 9:36 Pagina 17

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 23 24

Comments to this Manuals

No comments

Whirlpool KRSC 9060 Instruction for Use Page 17

Comments to this Manuals

Related products and manuals for Side-by-side fridge-freezers Whirlpool KRSC 9060