5
Undercounter Installation
NOTE: Installation hardware is not provided. See “Accessories”
for ordering conversion kit.
1. Measure the height of your kitchen cabinet opening. The top
of the compactor should be at least
¹₈" (3 mm) from the top
of the kitchen cabinet opening.
The rear wheels are preset for a kitchen cabinet opening
height of 34¹⁄₄" (87 cm) (position 1).
To adjust for other kitchen cabinet opening heights:
■ Loosen self-tapping screw enough to clear stud from hole
in position 1.
■ Move the rear wheel and stud to position 2 or 3 as
needed for your kitchen cabinet opening measurement:
Position 2: 34¹⁄₄" to 34⁷⁄₁₆" (87 to 87.5 cm)
Position 3: 34⁷⁄₁₆" to 34⁵⁄₈" (87.5 to 88 cm)
NOTE: To level the unit in position 3, you may need to
add shims under the front leveling legs.
■ Tighten screw.
■ Repeat for other rear wheel.
2. Use pliers to lower leveling legs away from compactor
cabinet.
3. Adjust legs so there will be a ¹⁄₈" (3 mm) to ¹₄" (6.4 mm) space
between the top of the compactor and the top of the kitchen
cabinet opening.
4. Stand the compactor upright.
5. Remove the plastic plugs from the compactor cabinet top.
6. Move the compactor close to its final location.
7. Plug into a grounded 3 prong outlet.
8. Determine whether you want the compactor cabinet or
drawer front flush with the kitchen cabinet face.
Using 2 - #8 - 18 x ⁵₁₆" mounting screws (provided in
conversion kit), attach the retaining brackets (provided in
conversion kit) to the compactor cabinet top as needed. See
“Accessories.”
NOTE: Installation hardware is not provided with full cabinet
models. See “Accessories” for ordering conversion kit.
■ If the compactor cabinet face is to be flush with the
kitchen cabinet face, place retaining bracket mounting
screws through “1.”
■ If the compactor drawer front is to be flush with the
kitchen cabinet face, place retaining bracket mounting
screws through “3.”
■ If the compactor is to be midway between “1” and “3,”
place the retaining bracket mounting screws through “2.”
9. Slowly lift the front slightly and roll compactor into the kitchen
cabinet opening.
10. Using 2 - #8 - 18 x ¹₂" mounting screws (provided in
conversion kit), fasten the retaining brackets (provided in
conversion kit) to the countertop with the mounting screws.
Countertop Mounting
NOTE: If retaining brackets cannot be attached to the underside
of countertop, attach mounting clips (provided in conversion kit)
to retaining brackets. Fasten compactor to kitchen cabinet face
with mounting screws through the mounting clips.
Cabinet-face Mounting
11. Grasp sides of compactor drawer and place bottom of
drawer into tracks.
12. Lift at the handle so drawer will go over drawer stops.
13. Close drawer.
A. Wheel bracket assembly
B. Compactor cabinet
C. Locating stud
D. Self-tapping screw (pivot)
A. Countertop
B. Retaining bracket (provided in conversion kit)
A. Countertop
B. Retaining bracket (provided in conversion kit)
C. Mounting screw (provided in conversion kit)
A. Mounting clip (provided
in conversion kit)
B. Kitchen cabinet
C. Retaining bracket (provided in
conversion kit)
D. Mounting screw (provided in
conversion kit)
(102 pages)
(24 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals