Whirlpool TCL 831 B (TK) Instruction for Use download pdf (Page 22)

Post Creasecare

((SSoonn KK››rr››ﬂﬂ››kkll››kk ÖÖnnlleemmee))

When selected, the clothes are occasionally tumbled

after the end of the drying and cool tumble cycles, to

help prevent creases developing should you not be

available to remove the load immediately the programme

is complete. The

SSoonn

light is on during this phase.

Empty Water

((SSuuyyuu BBooﬂﬂaalltt))

Light / Container

(If you have plumbed your dryer to a drain this light

can be ignored, as there is no need to empty the water

container).

When this light is on (not flashing) it reminds you to

empty the water container.

If the water container fills during a programme, the

heater turns off and the dryer does a period of Cool

Tumble then the light flashes and the buzzer sounds.

You must empty the water container and restart the

dryer or the clothes will not dry. After re-starting the

dryer, the light will take a few seconds to go out.

To avoid this always empty the water container each

time you use the dryer (see Maintenance).

●

Door Opening

Opening the door (or pressing the Start/Pause button

(Baﬂlat/Durdur) ) during a programme will stop the

dryer and have the following effects:

●

The Start/Pause light (Baﬂlat/Durdur) flashes

Amber.

●

During a delay phase the delay will continue to

count down. The Start/Pause button (Baﬂlat/Durdur)

must be pressed to resume the delay programme.

One of the delay lights will flash to show the

current delay setting.

●

The Start/Pause button (Baﬂlat/Durdur) must

be pressed to resume the programme. The

progress lights will change to show the current

status and the Start/Pause light (Baﬂlat/Durdur)

will stop flashing and turn green.

●

During the post creasecare (Son K›r›ﬂ›kl›k Önleme)

phase of a drying programme, the programme will

finish. Pressing the Start/Pause button (Baﬂlat/Durdur)

will re-start a new programme at the beginning.

●

Changing the programmes knob will select a new

programme and the Start/Pause light

(Baﬂlat/Durdur) will flash green. You can use this

to select the Cool Tumble programme (So¤uk

Döndürme) to cool the clothes, if you find them

dry enough. Press the Start/Pause button

(Baﬂlat/Durdur) to begin a new programme.

●

Note

If you have a power cut, switch off the power or

remove the plug. When power is restored, press the

Start/Pause button (Baﬂlat/Durdur) and the

programme will resume.

●

PROGRAMMES knob

! Warning, if after pressing the Start/Pause button

(Baﬂlat/Durdur) , the programmes knob position

has changed, the new position will NOT change the

programme selected.

To change a selected programme, press the

Start/Pause button (Baﬂlat/Durdur) ,the light

flashes Amber to indicate the programme is paused.

Select the new programme and any options required,

the light will then flash green. Press the Start/Pause

button (Baﬂlat/Durdur) again and the new

programme will start.

●

OPTION buttons / lights

These buttons are used to customise the selected

programme to your requirements. Not all options are

available for all programmes (see Start and Programmes).

If an option is not available and you press the button,

the buzzer will beep three times. If the option is

available there will be one beep and the option light

next to the button lights to confirm the selection.

Progress (Drying ‘

KKuurruuttuummaa’’

, Cool Tumble ‘

SSoo¤¤uukk

DDöönnddüürrmmee’’

, End ‘

SSoonn’’

) / Delay (3hr ‘

33ss’’

, 6hr ‘

66ss’’

, 9hr

‘

99ss’’

) Lights

When the light next to the delay button is on, these lights

flash to indicate the delay time selected. During other

programmes they indicate the progress of the dryer,

each one comes on as the corresponding phase starts.

Time Delay

((ZZaammaann EErrtteelleemmee))

The start of some programmes (see Start and

Programmes) can be delayed for up to 9 hours in 3hr

steps. Ensure the water bottle is emptied before setting

a delayed start.

When a delayed start is in progress the light next to the

delay button will be on and the selected delay period

light will flash (after the Start/Pause button (Baﬂlat/Durdur)

has been pressed).

To set a delayed start, press the Time Delay button,

and the light next to the button will come on together

with the 3hr delay light. Pressing the button again will

advance the delay setting to 6hr, the 3hr light goes

out and the 6hr light is on. Each time you press the

button the delay setting advances 3 hours, as indicated

by the corresponding light. If the 9hr light is on,

pressing the button again will cancel the delay.

Holding in the On/Off button (Açma/Kapama) will also

cancel.

Pre Creasecare

((ÖÖnn KK››rr››ﬂﬂ››kkll››kk ÖÖnnlleemmee))

When a delayed start and this option have been

selected the clothes are tumbled occasionally during

the delayed period to help prevent creases developing.

High Heat

((YYüükksseekk IIss››))

Available for Time Drying Programmes. Press this button

and a high heat setting is selected and the light next to

the button comes on. Timed programmes have a

default of low heat, if the light alongside the button is

on then pressing the button selects a low heat setting

and the light goes out.

The Controls

Start and Programmes

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 28

Comments to this Manuals

No comments

Whirlpool TCL 831 B (TK) Instruction for Use Page 22

Comments to this Manuals

Related products and manuals for Tumble dryers Whirlpool TCL 831 B (TK)