Whirlpool LTG6234D User Manual download pdf

Gas Washer/Dryer

PRODUCT MODEL NUMBER OVERALL DIMENSIONS

RECESSED AREA AND CLOSET INSTALLATION

DRAIN SYSTEM

EXHAUST VENTING

LTG6234D

Gas supply: Dryer is equipped for use with

NATURAL gas. Dryer can be converted to L.P. gas.

When rigid pipe is used it should be 1/2 inch IPS.

When acceptable to the gas supplier and local

codes, 3/8-inch approved tubing may be used for

lengths under 20 feet. For lengths over 20 feet,

larger tubing should be used. This washer/dryer is

equipped with its own permanent, flexible gas

connector, design-certified by CSA International,

for connecting the appliance to the gas supply line.

An individual manual shutoff valve must be

installed within 6 feet of the dryer in accordance

with the National Fuel Gas Code ANSI

Z223.1/NFPA 54.

Electrical: A 120-volt, 60-Hz., AC-only, 15- or

20-amp, fused electrical supply is required. A

time-delay fuse or circuit breaker is recommended.

It is also recommended that a separate circuit

serving only this appliance be provided.

Exhaust venting: Exhaust your dryer to the

outside. Four-inch diameter vent is required. Rigid

or flexible metal exhaust vent must be used. Do

not use plastic or metal foil vent. Exhaust outlet

hood must be at least 12 inches from the ground

or any object that may be in the path of the

exhaust. The dryer can be converted to exhaust

out right or left side.

Because Whirlpool Corporation policy includes a continuous commitment to improve

our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation

Instructions packed with product. Specifications subject to change without notice.

Ref. 8572777 Rev. A

12-12-05

Additional clearances might be required for wall, door and floor moldings.

Rear clearance may be 0" when house exhaust system is lined up directly with dryer exhaust.

Standpipe drain system - wall or floor

The standpipe drain requires a minimum diameter standpipe of 2" (5 cm). The minimum carry-away

capacity can be no less than 17 gal. (64 L) per minute. A 2" (5 cm) diameter to 1" (2.5 cm) diameter

standpipe adapter kit is available.

The top of the standpipe must be at least 39" (99 cm) high and no higher than 96" (2.4 m) from the

bottom of the washer.

Laundry tub drain system

The laundry tub needs a minimum 20 gal. (76 L) capacity. The top of the laundry tub must be at least

34" (86.4 cm) above the floor and no higher than 96" (2.4 m) from the bottom of the washer.

Floor drain system

The floor drain system requires a siphon break that may be purchased separately.

The siphon break must be a minimum of 28" (71 cm) from the bottom of the washer. Additional hoses

might be needed.

71 ⁵⁄₈ "

(181.9 cm)

*32"

(81.3 cm)

23 ³⁄₄ "

(60.3 cm)

32 ¹⁄₄ "

(81.9 cm)

27"

(68.6 cm)

A. Recessed area

B. Side view - closet or confined area

C. Closet door with vents

(2.5 cm)

(2.5cm)

27"

(68.6cm)

(2.5 cm)

32"

(81.3 cm)

¹⁄₂ "

(14 cm)

48 in.

(310 cm

)

24 in.

(155 cm

)

(15.2 cm)

(7.6 cm)

Vent Length Chart

No. of

90° turns

or elbows

Type of Vent Box or

Louvered

hoods

Angled

hoods

0 Rigid metal

Flexible metal

37 ft (11.3 m)

25 ft (7.6 m)

35 ft (10.7 m)

20 ft (6.1 m)

1 Rigid metal

Flexible metal

32 ft (9.7 m)

21 ft (6.4 m)

27 ft (8.2 m)

16 ft (4.9 m)

2 Rigid metal

Flexible metal

24 ft (7.3 m)

15 ft (4.6 m)

19 ft (5.8 m)

10 ft (3.0 m)

NOTE: Side and bottom exhaust adds a 90 turn inside the

washer/dryer. To determine maximum exhaust length, add one

90 turn to the chart.

1. Louvered hood style

2. Box hood style

(10.2 cm)

(6.4 cm)

Angled hood style

* Most installations require a

minimum 5¹⁄₂" (14 cm) clearance

behind the dryer for the exhaust

vent with elbow.

A. Louvered hood style

B. Box hood style

Plan installation to use the fewest number of elbows

and turns.

Maximum length of the exhaust system depends

upon the type of vent used, number of elbows and

the type of exhaust hood. The maximum length for

both rigid and flexible vent is shown in the chart.

Summary of Contents

Page 1 - B. Box hood style

®Gas Washer/DryerPRODUCT MODEL NUMBER OVERALL DIMENSIONSRECESSED AREA AND CLOSET INSTALLATIONDRAIN SYSTEMEXHAUST VENTINGLTG6234DGas supply: Dryer is e

Comments to this Manuals

No comments

Whirlpool LTG6234D User Manual

Browse online or download User Manual for Washers Whirlpool LTG6234D. Whirlpool LTG6234D User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Washers Whirlpool LTG6234D