Whirlpool AWM 8103/3 Instruction for Use download pdf (Page 12)

a.Water inlet fault (no or insufficient water

supply)

For models with a fault display, the “Water tap”

indicator is on or the display alternately shows “FH”.

Switch off the appliance by turning the programme

selector to the “ ” position and unplug it.

For models with no fault display, the washing

machine stops in the appropriate step. Switch off

the appliance and unplug it.

Check whether:

• the water tap is completely open, and the water

supply pressure is sufficient;

• the water inlet hose is kinked;

• the mesh filters are blocked (see “Care and

Maintenance” / “Water Hose Mesh Filters”);

• the water inlet hose is frozen.

Reconnect the appliance to the electrical supply.

For models with a fault display, reselect the desired

programme and press the “Start/Pause” button

again to continue with the programme (do not add

detergent for this programme).

For models without a fault display continue the

programme by pressing the “On/Off” button

again (do not add detergent for this programme).

If the fault re-occurs, contact After-Sales Service

(see “After-Sales Service”).

b.Draining out fault

For models with a fault display, depending on the

model, the display shows statically or alternately

“FP”. Switch off the appliance by turning the

programme selector to the “ ” position and

unplug it.

For models with no fault display, the washing

machine stops in the appropriate step. Switch off

the appliance and unplug it.

Check whether:

• the drain hose is kinked (see “Installation

Guide”);

• the pump / filter are blocked (see “Removing the

Filter / Draining Residual Water”);

IMPORTANT: before draining, allow the wash

water to cool down.

• the drain hose is frozen.

Connect the appliance to the electrical supply.

For models with a fault display reselect the desired

programme and press the “Start/Pause” button

again to continue with the programme (do not add

detergent for this programme).

For models without a fault display continue the

programme by pressing the “On/Off” button

again (do not add detergent for this programme).

If the fault re-occurs, contact After-Sales Service

(see “After-Sales Service”).

c.Electrical module fault

For models with a fault display “F4” to “F15” are

displayed and some or all Spin Speed Selection

LEDs are flashing. Switch off the appliance. Select a

programme and press the “Start/Pause” button

once again. The programme will continue.

For models without a fault display the washing

machine stops in the appropriate step. Switch the

appliance first off, then on. The programme will

continue.

If the fault re-occurs, contact After Sales Service

(See “After-Sales Service”).

d.Water Stop fault (if available)

The “Water Stop” may have been triggered by:

1.too much foam.

2.a leak in the inlet hose or in the appliance.

In this case the pump is switched on automatically

in order to pump the water out.

For models with a fault display the light of the

“Water Stop” indication is on. The display shows

“FA” or alternately “F” and “A” and the pump is

running. Switch off the appliance by turning the

programme selector to the “ ” position, unplug

the appliance and make sure that the water tap is

closed.

For models without a fault display the washing

machine stops in the appropriate step. Switch off

the appliance, , unplug the appliance and make sure

that the water tap is closed.

Tilt the appliance forwards carefully to allow the

collected water to flow out.

Then:

1.plug in the appliance,

2.turn the water tap on (if water immediately flows

into the appliance again, without the appliance

being started, close water supply and call After-

Sales Service).

For models with a fault display reselect the desired

programme and press the “Start/Pause” button

again to continue with the programme (do not add

detergent for this programme).

For models without a fault display continue the

programme by pressing the “On/Off” button

again (do not add detergent for this programme).

If the fault re-occurs, contact After-Sales Service

(see “After-Sales Service”).

3gb10161.fm Page 27 Thursday, May 6, 2004 6:36 PM

1 2 ... 7 8 9 10 11 12 13 14

Comments to this Manuals

No comments

Whirlpool AWM 8103/3 Instruction for Use Page 12

Comments to this Manuals

Related products and manuals for Washing machines Whirlpool AWM 8103/3