Whirlpool AWZ 812 D Instruction for Use download pdf (Page 2)

GB 2

BEFORE USING THE WASHING MACHINE

1.Removing the packaging and inspection

•

After unpacking, make sure that the washing

machine is undamaged. If in doubt, do not use the

washing machine. Contact After-Sales Service or

your local retailer.

•

Check that the accessories and supplied parts are

all present.

•

Keep the packaging materials (plastic bags,

polystyrene parts, etc.) out of reach of children,

as they are potentially dangerous.

•

If the appliance was exposed to the cold before

delivery, keep it at room temperature for a few

hours before operating.

2.Remove the transport bolts

•

The washing machine is fitted with transport

bolts to avoid any possible damage to the interior

during transport. Before using the washing

machine, it is imperative that the transport bolts

are removed.

•

After their removal, cover the openings with the

4 enclosed plastic caps.

3.Install the washing machine

•

You are advised not to install the appliance in a

room where the temperature could drop to

below 0°C.

•

Given the weight of the appliance, attention must

be paid to safety standards when it is being moved.

•

When positioning the appliance, make sure that

the power cable is not kinked or compressed and

that it can be easily accessed if required.

•

Remove the protective film from the control

panel (if available on your model).

•

Move the appliance without carrying it by the

worktop.

•

Install the appliance on a solid and level floor

surface, preferably in a corner of the room.

•

Make sure that all four feet are stable and resting

on the floor and then check that the washing

machine is perfectly level (use a spirit level).

•

In case of wooden or so-called “floating floors”

(for instance certain parquet or laminate floors),

place the appliance on a 60 x 60 cm sheet of

plywood at least 3 cm in thickness which is

secured to the floor.

•

If the washing machine is installed on a carpeted

floor, leave sufficient space between the

appliance and the floor to guarantee the free

circulation of air.

4.Water supply

•

Connect the water supply inlet hose in

accordance with the regulations of your local

water company.

•

Water supply: Cold water only (unless

otherwise indicated on

the programme chart)

•

Water tap: 3/4” threaded hose

connector”

•

Water pressure

(flow pressure): 100-1000 kPa (1-10 bar).

•

Use only new hoses to connect the washing

machine to the water supply. Used hoses must

not be used and should be discarded,

5.Drain

•

Connect the drain hose to the siphon or hook it

over the edge of a sink by means of the “U” bend

supplied.

•

If the washing machine is connected to an

integrated drainage system, ensure the latter is

equipped with a vent to avoid simultaneous

loading and draining of water (siphoning effect).

6.Electrical connections

•

Electrical connections must be carried out by a

qualified technician in compliance with the

manufacturer’s instructions and current standard

safety regulations.

•

Voltage, power consumption and electrical

protection data are supplied on the inside of the

appliance door.

•

The washing machine must be connected

exclusively by means of a socket with an earth

connection in accordance with current

regulations. The washing machine must be

earthed by law. The manufacturer declines all

liability for possible damage to property or injury

to persons or pets deriving from failure to

observe the a/m directions.

•

Do not use extension leads or multi sockets.

•

Before any maintenance on the washing machine

disconnect it from the mains supply.

•

After installation, access to the mains plug or to

disconnection from mains supply must be

ensured at all times via a double-pole switch.

•

Do not operate the washing machine if it has

been damaged during transport. Inform the

After-Sales Service.

•

Mains cable replacement is only to be carried out

by After-Sales Service.

•

Use the appliance only for domestic washing and

for its intended applications.

Minimum housing dimensions:

Width: 600 mm

Height: 850 mm

Depth: 600 mm

30120042GB.fm Page 2 Thursday, January 8, 2009 6:07 PM

Black process 45.0° 150.0 LPI

1 2 3 4 5 6 7 ... 13 14

Comments to this Manuals

No comments

Whirlpool AWZ 812 D Instruction for Use Page 2

Comments to this Manuals

Related products and manuals for Washing machines Whirlpool AWZ 812 D