Whirlpool WAOT 864 Use and Care Guide download pdf (Page 15)

When using the two preset cycles “Waschen &

Trocknen 45’” and “Waschen & Trocknen 90’”, it is

not necessary to select and start a drying cycle.

Dry only

This function is used to simply dry a wet load

washed previously in the washer dryer or by

hand.

1. Select a programme that's compatible with

the type of garments to be dried (e.g. select

cotton if you want to dry a load of wet cotton

garments).

2. Press the button to perform the drying cycle

alone, without performing the wash cycle.

3. Select the desired drying mode by pressing

the button.Two drying modes are available:

automatic or timer.

- Automatic drying with selectable levels:

In automatic drying mode, the washer dryer

machine dries the laundry until the set level of

dryness is reached. As soon as the button has

been pressed, the washer dryer automatically

selects the maximum drying level compatible

with the selected programme. Press the button

again to reduce the drying level.

The following levels are available:

Wardrobe : laundry is completely dry and

ready to be put away in the wardrobe without

ironing.

Hanger : laundry is left slightly damp to

minimise creasing. Garments must be hung to

air dry completely.

Iron : garments are left reasonably damp to

make ironing easier.

- Timer drying mode:

If you want to set a timed drying cycle, press the

button repeatedly. After all the automatic

drying levels have been displayed, continue

pressing the button until the desired time

is displayed. Values from 210 to 30 minutes are

settable.

N.B.: always allow a cooling down period after

drying before opening the door.

5. USING THE CORRECT AMOUNT OF

DETERGENT.

Extract the dispenser and pour the detergent

into the appropriate trays as explained in the

section titled “Detergent Dispenser”. Only if

you want to perform a wash or wash + dry

programme.

6. DELAYING THE START OF A PROGRAMME.

If you want to delay the programme's

activation, see the section titled“Programmes

and Options”.

7. STARTING A PROGRAMME.

Press the START/PAUSE button. The relative

indicator lamp illuminates, the door locks

and the door open symbol extinguishes.

To change a programme while a cycle is in

progress, set the washer dryer to pause mode

by pressing the START/PAUSE button (the

START/PAUSE indicator light will slowly ash

with an amber colour); next, select the desired

cycle and press the START/PAUSE button again.

To open the door while a cycle is in progress,

press the START/PAUSE button; if the symbol

turns on, the door can be opened. Press the

START/PAUSE button again to resume the

programme from the point at which it was

interrupted.

8. CANCELLING A PROGRAMME IN PROGRESS IF

NECESSARY

Press and hold the button until the washer

dryer stops.

If the water level and temperature are low

enough, the door unlocks and may be opened.

The door remains locked if there is water in the

drum. To unlock the door, switch the washer

dryer on, select the SCHLEUDERN & ABPUMPEN

programme and turn the spin function o

by setting the spin speed to 0. The water is

emptied and the door unlocks at the end of the

programme.

9. SHUT OFF THE WASHER DRYER AT THE END

OF THE PROGRAMME.

At the end of the cycle, the message “END” is

shown on the display. The door can only be

opened once the symbol turns on. Check

that the door unlocked symbol is lit, then open

the door and take out the laundry.

Press to switch the washer dryer o. To save

energy, if the washer dryer is not switched

o manually with the button, it turns o

automatically approximately 30 minutes after

the end of the programme.

Leave the door slightly ajar in order to allow the

inside of the washer dryer to dry.

1 ... 14 15 16 ... 39

Comments to this Manuals

No comments

Whirlpool WAOT 864 Use and Care Guide Page 15

Comments to this Manuals

Related products and manuals for Washing machines Whirlpool WAOT 864