Whirlpool WFW560CHW Use and Care Manual download pdf (Page 6)

Washing

During the wash cycle, this will display to let you know

the cycle is in progress.

Drying (on some models)

During a drying cycle, this will display to let you know

the drying cycle is in progress.

Cool Down (on some models)

At the end of a drying cycle, your load will go through

a cool-down period.

PreSoak

This symbol will be displayed to let you know

a presoak is in progress.

Detergent Low (on some models)

When detergent in the bulk dispenser is running low,

the display will show the detergent level (Low).

Add Garment

When “Add Garment” is displayed, you may pause the

washer, open the door, and add items. Touch and hold

START/PAUSE to start the washer again.

Door Locked

The Door Locked symbol will display to

indicate that the door is locked and cannot

be opened without rst pausing or canceling the cycle.

Control Lock

When the Contol Lock symbol is displayed,

the buttons are disabled. Touch and hold EXTRA

RINSE for 3 seconds to enable the buttons.

FanFresh

(on some models)

This symbol will be displayed when the FanFresh

option is activated. The fan will turn on and the

load will tumble periodically for up to 12 hours.

End

Once the cycle is complete, “End” will display. Remove

the load promptly for best results.

CYCLE MODIFIERS

When you select a cycle, its default settings will light up.

Touch to adjust cycle modiers on the washer before

touching START/PAUSE. Additional wash modiers or

options selected after touching Start/Pause may not activate.

Once a wash setting is selected, it is saved for the cycle

selected. To return to factory default cycle settings, unplug

washer for 30 seconds; then plug back in. See “Cycle Guide”

for default cycle settings.

NOTE:

Some modiers

may increase or decrease the

estimated time remaining.

Temp

The recommended wash temperature is preset for

each cycle. Some preset temperatures can be changed.

You may select a different wash temperature based on

the level of soil and type of fabric being washed. For

best results, use the warmest wash water safe for your

fabric, following the garment label instructions. All wash

temperatures feature a cold rinse.

Spin

The recommended spin speed is preset for each cycle.

Some preset speeds can be changed.

■ Faster spin speeds mean shorter dry times, but may

increase wrinkling in your load.

■ Slower spin speeds reduce wrinkling, but will leave

your load more damp.

Soil

The recommended soil level is preset for each cycle.

Some preset soil levels can be changed. For heavily

soiled and sturdy fabrics, select the Heavy Soil Level

setting. For lightly soiled and delicate fabrics, select the

Light Soil Level setting. Lower soil level settings will help

reduce tangling and wrinkling.

hold 3 sec for

Cycle Signal

hold 3 sec for

Control Lock

hold 3 sec for

FanFresh

hold 3 sec for

PreSoak

UTILITY CYCLES

Clean Washer

Use this every 30 washes to keep the inside of your

washer fresh and clean. This cycle uses a higher water

level. Use with affresh

Washer Cleaner tablets or liquid

chlorine bleach to thoroughly clean the inside of your

washer. When using this cycle, the drum should be

empty. This cycle should not be interrupted. See the

“Washer Care” section.

Drain & Spin

This cycle removes excess water from the load or

special-care items washed by hand. Use this cycle

after a power failure. For some fabrics, you may choose

to set a slower spin speed. On some models: Touch

and hold DRAIN & SPIN for 3 seconds to set a Dry Only

cycle.

CYCLE OPTIONS

You may add or remove options for each cycle. Not all

options can be used with all cycles, and some are preset

to work with certain cycles. Options vary by model.

Steam Clean (on some models)

The Steam Clean option adds additional soak and

wash time to many cycles to help remove tough stains,

as well as a steam boost for added cleaning power.

An integrated heater helps to maintain optimal wash

temperatures. See “Cycle Guide” for cycles that allow

the Steam Clean option.

You can also touch and hold STEAM CLEAN

for 3 seconds to turn cycle signals on or off.

Extra Rinse

Activate this option to add an extra rinse to most

cycles.

You can also touch and hold EXTRA RINSE

for 3 seconds to disable/enable the Control Lock.

Wash & Dry (on some models)

Touch to add a drying cycle to your load after the wash

cycle has nished. The Wash & Dry option is designed

to wash and dry small loads overnight. Cycle time

will vary based on load composition. For optimal dry

performance and cycle time, load the drum no more

than one-quarter full. The cycle will automatically

terminate after a maximum 12-hour cycle time.

You can also touch and hold WASH & DRY for

3 seconds to activate/deactivate the FanFresh

option. Use the FanFresh

option if you will be

unable to remove the load promptly. The washer

will automatically activate the fan after the cycle ends

and tumble the load periodically for up to 12 hours.

IMPORTANT:

■ Do not use dryer sheets.

■ Do not dry comforters or large blankets.

Load & Go™ (on some models)

Touch to select this option If you want to automatically

add HE detergent to the wash load at the proper time.

IMPORTANT: When using the dispenser cartridge

with concentrated liquid detergent, be sure to change

the detergent concentration settings in the control if

the detergent used is different than factory preset of

2x concentration. Change the detergent concentration

setting by touching and holding TEMP and SOIL for

3 seconds.

You can also touch and hold LOAD & GO™ for 3

seconds to set a presoak.

PreSoak (on some models)

Touch to add a presoak time of your choice

to a wash cycle.

hold 3 sec for

Cycle Signal

hold 3 sec for

Control Lock

hold 3 sec for

FanFresh

hold 3 sec for

PreSoak

1 2 3 4 5 6 7 8 9 10 11 ... 70 71

Comments to this Manuals

No comments

Whirlpool WFW560CHW Use and Care Manual Page 6

Comments to this Manuals

Related products and manuals for Washing machines Whirlpool WFW560CHW