EN
Quick guide
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT
In order to receive a more complete assistance, please
register your product on www . whirlpool . eu/ register
Before using the appliance carefully read the Safety
Instruction.
PRODUCT DESCRIPTION
FIRST TIME USE
AIR VENT FOR THE SUCTION VERSIONS
Connect the hood and discharge holes on the walls with a diameter
equivalent to the air outlet (connection ange).
Using the tubes and discharge holes on walls with smaller dimensions
will cause a diminution of the suction performance and a drastic
increase in noise.
Any responsibility in the matter is therefore declined.
! Use a duct of the minimum indispensible length.
! Use a duct with as few elbows as possible (maximum elbow angle: 90°).
! Avoid drastic changes in the duct cross-section.
! The company declines any responsibility whenever these regulations
are not respected.
FILTERING OR DUCTING?
! Your cooker hood is ready to be used in suction version.
To use the hood in ltering version the special ACCESSORY KIT must be
installed.
Check if the ACCESSORY KIT is furnished or must be bought separately.
Note: If furnished, in certain cases, the additional activated carbon ltering
system may be installed on the hood. Information about the conversion of
the hood from suction version to ltering version is present in the Manual
“Safety Instructions & Installation”.
DUCTING VERSION
In this case the fumes are conveyed outside of the building by means
of a special pipe connected with the connection ring located on top of
the hood.
Attention! The exhausting pipe is not supplied and must be purchased
apart. Diameter of the exhausting pipe must be equal to that of the
connection ring.
Attention! If the hood is supplied with active charcoal lter, then it
must be removed.
FILTER VERSION
The aspirated air will be degreased and deodorised before being fed
back into the room.
In order to use the hood in this version, you have to install a system of
additional ltering based on activated charcoal.
CONTROL PANEL
The control panel consists of a backlit rotary disk.
• To switch the lights on and o:
Press the disk (T) to switch the lights on and o.
• To select the suction speed:
Turn the disk (T) clockwise to activate and increase the suction
speed, or anti-clockwise to decrease it and switch o the hood.
The crown (L) lights up to indicate the selected suction speed:
• L1 on
speed 1 (minimum)
• L1+L2 on
speed 2 (medium)
• L1+L2+L3 on
speed 3 (maximum)
• L1+L2+L3+L4 ashing
speed 4 (intense): (lasts 5 minutes, then the hood switches
automatically to speed 2)
• L o
suction motor switched o
Filter saturation control device
The hood is tted with a device that indicates when lter maintenance
is needed.
The grease lter saturation control device is always active.
The active carbon lter control device is usually deactivated.
To activate it, proceed as follows:
- Switch o the hood.
- Press the disk (T) for more than 5 seconds.
The crown (L) will light up completely, ashing, and an acoustic signal
is emitted to indicate that the carbon lter control device is active.
Please note: to deactivate it, switch o the hood and press the disk (T).
The backlight on L1+L2 will ash. Wait for the acoustic signal that conrms
deactivation.
Grease lter saturation signal
L1 + L2 ash when maintenance is needed on the grease lter.
Active carbon lter saturation signal
L3 + L4 ash when maintenance is needed on the active carbon lter.
* Available only on certain models
(20 pages)
(88 pages)
(68 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals