GB
-1-
Chart
START/RESUME BUTTON
Push this button to start the selected program: the
indicator lights up and goes off at the end of the
program.
When the door is opened during a washing cycle,
the cycle is temporarily paused: the Start indicator
blinks. To resume the cycle close the door and
push Start button again.
CANCEL/OFF BUTTON
Push this button to switch off the control panel.
If pressed when a program is running it cancels the
program ongoing draining water for 1 minute
(0:01 is shown into the display).
If pressed when the dishwasher is switched off,
it drains any possible liquids from dishwasher
(1 minute process).
PROGRAM SELECTION
BUTTON
Push “Programs” button
(repeatedly) until the indicator
of the required program lights
up (see “Table of programs”
below).
(see at right for options description)
1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional
options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the
appliance’s automatic calibration system.
2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the
EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.
Table of programs
Deter-
gent
Consumption
P
Programs
Available
options
Loading instructions
Litres kWh
Minutes
1)
1
AutoSensor 50-65°C
Delay
Half Load
Recommended program for routine
washes, with dried-on food (e.g. EN
50242).
X 7-14 1.00-1.60 70-155
2
Pre-Wash cold
Delay Crockery to be washed later. — 4.0 0.03 14
3
Quickwash 45°C
Delay
Lightly soiled crockery, with no dried-
on food.
X 11.0 0.80 30
4
Eco
2)
50°C
Delay
Half Load
Normally soiled crockery. X 11.5 1.05 150
5
Intensive 70°C
Delay
Recommended program for heavily
soiled crockery, especially suitable for
pans and saucepans.
X 14.0 1.55 155
5019 396 01992ADP 7740
Options and display description
SALT INDICATOR
When lit (at the end of the cycle),
the salt reservoir needs to be
refilled.
HALF LOAD BUTTON
Half load cycle can be used for the
upper or lower rack. Select the
required program then press the
“Half Load” button - the light
comes on. Turns off at the end of
the program.
The “Half Load” option can be
used with the programs
indicated in the table of
programs.
TABLET SETTING
This setting allows to optimize the cycle performances
according the type of detergent used.
Push the Tablet button for 3 seconds (until the indicator lights
up) if you are using the combined detergents in tablet (rinse aid,
salt and detergent in 1 dose).
If you are using powder detergent or liquid detergent, the
Tablet indicator on the control panel has to be off.
DELAYED START BUTTON
Push the button (repeatedly)
to delay the start of the
program. Adjustable from 1 to
24 hours. With each press of
the button, the delayed start
indicator increases by one
hour and after 24 restarts from
0. Then press the START
button. The dishwasher will
start after the set time.
RINSE AID INDICATOR
When lit (at the end of the cycle),
the rinse aid dispenser needs to
be refilled.
WASH TIME DISPLAY
Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates
the time remaining until program start (h.00) - below 1h (0:min).
If “Fx Ey” messages appears on the display, see page 6 - chapter “What to do if...”.
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ
THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING
ANY BUTTON EXCEPT CANCEL/OFF BUTTON.
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES
AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.
Quick reference guide
Comments to this Manuals