Whirlpool GSFP 6140 A+ WS Instruction for Use download pdf

-1-

Chart

PROGRAMS SELECTION

BUTTON

Push “Programs” button

(repeatedly) until the indicator

of the required program lights

up (see “Table of programs”

below).

START/RESUME BUTTON

Push this button to start the selected program: the

indicator lights up and goes off at the end of the

program.

When the door is opened during a washing cycle,

the cycle is temporarily paused: the Start indicator

blinks. To resume the cycle close the door and

push Start button again.

CANCEL/OFF BUTTON

Push this button to switch off the control panel.

If pressed when a program is running it cancels the

program ongoing draining water for 1 minute

(0:01 is shown into the display).

If pressed when the dishwasher is switched off,

it drains any possible liquids from dishwasher

(1 minute process).

(see at right for options description)

1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional options) and may vary

depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.

2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the

EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.

3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.

Table of programs

Deter-

gent

Consumption

Programs

Available

options

Loading instructions

Litres kWh

Minutes

Sensor 40-70°C

Delay

Multizone

Antibacterial

rinse

Normally or heavily soiled crockery,

including pots and pans. Thanks to steam

action, soaking or hand pretreatment is no

longer needed. In addition hygiene is

ensured due to the high temperature steam.

X 7-14 0.99-1.80 70-185

Pre-Wash cold

Delay

Multizone

Crockery to be washed later. — 4.0 0.03 14

Quickwash 45°C

Delay

Multizone

Lightly soiled crockery, with no dried-

on food.

X 11.0 0.80 30

Bio Normal

50°C

Delay

Multizone

Antibacterial

rinse

Normally soiled crockery.

Energy-saving program.

X 11.0 0.98 150

Fast Everyday 60°C

Delay

Multizone

Normally soiled crockery. X 10.0 1.30 80

Intensive 70°C

Delay

Multizone

Antibacterial

rinse

Recommended program for heavily

soiled crockery, especially suitable for

pans and saucepans.

X 14.0 1.55 155

5019 496 01673GSFP 6140 A+

BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ

THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!

Options and display description

SALT INDICATOR

When lit (at the end of the cycle),

the salt reservoir needs to be

refilled.

MULTIZONE

Allows you to choose the washing

zones. Press this button (repeatedly)

to select the wash zones:

both racks

only lower rack

only upper rack

- indicator lits

TABLET SETTING

This setting allows to

optimize the cycle

performances according

the type of detergent

used. Push the Tablet

button for 3 seconds (until

the indicator lights up) if

you are using the

combined detergents in

tablet (rinse aid, salt and

detergent in 1 dose). If you

are using powder

detergent or liquid

detergent, the Tablet

indicator on the control

panel has to be off.

DELAYED START

BUTTON

Push the button

(repeatedly) to delay the

start of the program.

Adjustable from 1 to 24

hours. With each press of

the button, the delayed

start indicator increases

by one hour and after 24

restarts from 0. Then

press the START button.

The dishwasher will start

after the set time.

RINSE AID INDICATOR

When lit (at the end of the cycle),

the rinse aid dispenser needs to

be refilled.

WASH TIME DISPLAY

Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates

the time remaining until program start (h.00) - below 1h (0:min).

If “Fx Ey” messages appears on the display, see page 6 - chapter “What to do if...”.

ANTIBACTERIAL RINSE

This function activates an

antibacterial rinse at the end of the

wash cycle, guaranteeing a further

reduction of bacteria. Press the

button to activate or deactivate the

function. This function can be used

with the programs indicated in the

table of programs. The dishwasher

door must be kept shut for the entire

duration of the program in order to

guarantee reduction of bacteria. If

the door is opened the indicator lamp

starts flashing.

THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING

ANY BUTTON EXCEPT CANCEL/OFF BUTTON.

FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES

AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.

Quick reference guide

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - 5019 496 01673GSFP 6140 A+

GB -1-ChartPROGRAMS SELECTION BUTTONPush “Programs” button (repeatedly) until the indicator of the required program lights up (see “Table of programs”

Page 2 - Daily check

GB -2-First time use1- salt reservoir2- rinse aid dispenser3- detergent dispenser4- racks system5,6,7,8- available functions on the panel9- filters10-

Page 3 - Daily use

GB -3-Daily check3Check the rinse aid indicator to check the level into the dispenser.(depending on the model)Rinse aid indicator on the control panel

Page 4 - How to load the racks

GB -4-How to load the racksD - OPEN(depending on the model)E - Foldable plate holders: they can be folded down to load potsorFixed plate holdersF - Cu

Page 5 - Maintenance and care

GB -5-Switching off the appliance. Everything OK...Wash cycleSelect program678Maintenance and careMaintenance and careOverview of programsThe max. pos

Page 6 - What to do if

GB -6-What to do if...If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem.Most fault

Page 7

GB -7-What to do if...Crockery and cutlery... Possible causes... Solutions...salt indicator lit- Use tablets for soft water. - Set “Tablet” option;

Page 8

GB -8-What to do if...If, after carrying out the above checks, the fault persists, disconnect the mains plug and turn off the water tap. Contact the A