EN -1-
Chart
(see at right for options description)
PROGRAM SELECTION
BUTTON
Push “P” button (repeatedly)
until selected program number
is shown on the display
(P1...Px) - see “Table of
programs” below.
START/RESUME BUTTON
Push this button to start the selected program: the
indicator lights up and goes off at the end of the program.
When the door is opened during a washing cycle, the
cycle is temporarily paused: the Start indicator blinks.
To resume the cycle push Start button and close
the door within 3 seconds.
CANCEL/OFF BUTTON
Push this button to switch off the control panel.
If pressed when a program is running it cancels
the program ongoing draining water for 1 minute
(0:01 is shown into the display). If pressed when
the dishwasher is switched off, it drains any
possible liquids from dishwasher (1 minute
process).
1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without any options) and may vary depending on
conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.
2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/Standard
loading comparison test and other tests, contact (only in English) use following address “
[email protected]”.
3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.
RECYCLING WATER SYSTEM: these programs save water in a dedicated tank.
A TANK CLEANING CYCLE (at least 45 min.) is automatically run every 30 cycles or after every power off, to assure the best product conditions.
* Power consumption in: Left-on mode: 0.70 W. Off-mode: 0.40 W.
Table of programs
Deter-
gent
Consumption
Drying
phase
Programs
Available
options
Loading instructions
Litres kWh
Minutes
1)
P1
Sensor Power
Clean Plus
40-70°C
Delay
Antibacterial
rinse
Power Clean
Use for normal soiled dishes with dried-on
food. Senses the level of soiling on the dishes
and adjusts the program accordingly. When
the sensor is detecting the soil level an
animation appears in the display and the cycle
duration is updated. The Power Clean option
is activated automatically with this program.
To deactivate, press the Power Clean button
on the control panel.
X 7-15 1.00-1.70 70-172 Full
P2
Pre-Wash cold
Delay Crockery to be washed later. – 4.0 0.01 14-16 NO
P3
Glass 40°C
Delay Light soiling, for example glasses and cups. X 10.5 0.85 105-114 Light
P4
Express 45°C
Delay Lightly soiled crockery, with no dried-on food. X 11.0 0.85 30-50 NO
P5
Eco
2)
50°C
Delay
Antibacterial
rinse
Power Clean
Normally soiled crockery.
Standard program, the most efficient in terms
of combined energy and water consumption.
X 6.0 1.03 185 Full
P6
Normal 60°C
Delay
Antibacterial
rinse
Normally soiled crockery. X 11.0 1.30 80-95 Full
P7
Half Load 50°C
Delay
Ideal for washing a half load of lightly or
normally soiled crockery.
X 7.5 1.00 75-80 Full
P8
Intensive 65°C
Delay
Antibacterial
rinse
Power Clean
Recommended program for heavily soiled
crockery, especially suitable for pans and
saucepans.
X 11.0 1.60 165-175 Full
5019 400 00170
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS
QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
Options and display description
WASH TIME DISPLAY
Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates
the time remaining until program start (h.00) - below 1h (0:min).
If “Fx Ey” messages appears on the display, see page 6 - chapter “What to do if...”.
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY
BUTTON EXCEPT CANCEL/OFF BUTTON. FOR ENERGY SAVING THE
CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER
30 SECONDS IF NO CYCLE HAS STARTED.
SALT INDICATOR
When lit (at the end of the cycle), the
salt reservoir needs to be refilled.
RINSE AID INDICATOR
When lit (at the end of the cycle), the
rinse aid dispenser needs to be refilled.
OPERATION
INDICATOR
A LED light
projected on the
floor indicates that
the dishwasher is
working.
POWER CLEAN PLUS
Thanks to the additional power
jets this option provides a more
intensive and powerful wash in the
lower rack, in the specific area.
This option is recommended for
washing pots and casseroles
(see page 4). Press this button
to activate Power Clean (the
indicator lights up).
For non Power Clean loading
to achieve best cleaning
performances and resources
optimization, Power Clean should
be switched off.
ANTIBACTERIAL RINSE
2
)
This function activates an antibacterial
rinse at the end of the wash cycle,
guaranteeing a further reduction of
bacteria. Press the button to activate
or deactivate the function.
This function can be used with the
programs indicated in the table of
programs. The dishwasher door must
be kept shut for the entire duration of
the program in order to guarantee
reduction of bacteria. If the door is
opened the indicator lamp starts
flashing.
TABLET SETTING
This setting allows to
optimize the cycle
performances according
the type of detergent
used. Push the Tablet
button for 3 seconds
(until the indicator lights
up) if you are using the
combined detergents in
tablet (rinse aid, salt and
detergent in 1 dose).
If you are using powder
detergent or liquid
detergent, the Tablet
indicator on the control
panel has to be off.
DELAYED START
BUTTON
Push the button
(repeatedly) to delay the
start of the program.
Adjustable from 1 to 24
hours. With each press of
the button, the delayed
start indicator increases
by one hour and after
24 restarts from 0.
Then press the START
button. The dishwasher
will start after the set
time.
Quick reference guide
Bauknecht is a registered trademark
(8 pages)
(8 pages)
(8 pages)
(31 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals