Whirlpool WDF550SAFW Use and Care Manual download pdf (Page 5)

1. Remove the filter assembly by

turning the Main filter ¹⁄₄ turn

counterclockwise. Lift to

remove.

2. Clean the Main filter and Fine

filter using a cleaning brush.

3. Reassemble the filter parts as

shown in the illustration.

4. Reinsert the entire filter

assembly in the dishwasher,

positioning it in place.

5. Turn the Main filter ¹⁄₄ turn

clockwise to secure in place.

NOTE: The dishwasher should not

be operated without the filter

assembly installed. Improper

replacement of the filter assembly

may reduce the performance level

of the appliance and may damage dishes and utensils.

Storing the Dishwasher

If you will not be using the dishwasher during the summer months,

turn off the water and power supply to the dishwasher. In the

winter, if the dishwasher could be exposed to near freezing

temperatures or is left in a seasonal dwelling such as a second

home or vacation home, avoid water damage by having your

dishwasher winterized by authorized service personnel.

Troubleshooting

First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)

to possibly avoid the cost of a service call.

In the U.S.A., www.whirlpool.com In Canada, www.whirlpool.ca

Dishwasher is not operating properly

■

Dishwasher does not run or stops during a cycle

Is the door closed tightly and latched?

Is the right cycle selected?

Is the START/RESUME light on? Press START/RESUME.

Is there power to the dishwasher? Has a household fuse blown,

or has a circuit breaker tripped? Replace the fuse or reset the

circuit breaker. If the problem continues, call an electrician.

Has the motor stopped due to an overload? The motor

automatically resets itself within a few minutes. If it does not

restart, call for service.

Is the water shutoff valve (if installed) turned on?

■

Water remains in the dishwasher

Is the cycle complete?

■

Detergent remains in the covered section of the dispenser

Is the cycle complete?

Is the detergent lump-free? Replace detergent if necessary.

■

White residue on the front of the access panel

Was too much detergent used?

Is the brand of detergent making excess foam? Try a different

brand to reduce foaming and eliminate buildup.

■

Odor in the dishwasher

Are dishes washed only every 2 or 3 days? Run a rinse cycle

once or twice a day until you have a full load.

Does the dishwasher have a new plastic smell? Run a vinegar

rinse as described in “Dishwasher Care.”

■

Condensation on the kitchen counter (built-in models)

Is the dishwasher aligned with the countertop? Moisture from

the vent in the dishwasher console can form on the counter.

Refer to the Installation Instructions for more information.

Dishes do not dry completely

■

Dishes do not dry completely

Did you use a rinse aid? Your dishwasher is designed to use

rinse aid for good drying performance. Without rinse aid your

dishes and dishwasher interior will have excessive moisture.

The heat dry option will not perform as well without rinse aid.

■

Dishes are not dry

Did you load your dishwasher to allow proper water drainage?

Do not overload. Use a liquid rinse aid to speed drying.

Are the plastics wet? Plastics often need towel drying.

Is the rinse aid dispenser empty?

Did you use an air-dry or energy-saving dry option? Use a

heated drying option for dryer dishes.

■

Excess moisture on racks and dishwasher interior

Check the rinse aid indicator to see that there is rinse aid in the

dispenser.

Spots and stains on dishes

■

Spotting and filming on dishes

Is your water hard, or is there a high mineral content in your

water? Conditioning the final rinse water with a liquid rinse aid

helps eliminate spotting and filming. Keep the rinse aid

dispenser filled. Always use a high-temp option. If your water

hardness is 13 grains or above, it is strongly recommended that

you install a home water softener. If you do not wish to drink

softened water, have the softener installed onto your hot water

supply.

Is the water temperature too low? For best dishwashing results,

water should be 120°F (49°C) as it enters the dishwasher.

Did you use the correct amount of effective detergent? Use

recommended dishwasher detergents only. Do not use less

than 1 tbs (15 g) per load. Detergent must be fresh to be

effective. Heavy soil and/or hard water generally require extra

detergent.

Is the home water pressure high enough for proper dishwasher

filling? Home water pressure should be 20 to 120 psi (138 to

828 kPa) for proper dishwasher fill. If you have questions about

your water pressure, call a licensed, qualified plumber.

NOTE: To remove spots and film from glassware, remove all

silverware and metal items and run a vinegar rinse as described

in “Dishwasher Care.”

■

Silica film or etching (silica film is a milky, rainbow-colored

deposit; etching is a cloudy film)

Sometimes there is a water/chemical reaction with certain

types of glassware. This is usually caused by some

combination of soft or softened water, alkaline washing

solutions, insufficient rinsing, overloading the dishwasher, and

the heat of drying. It might not be possible to avoid the

problem, except by hand washing.

A. Main filter

B. Metal strainer

C. Fine filter

1 2 3 4 5 6 7 8 9 10 ... 15 16

Comments to this Manuals

No comments

Whirlpool WDF550SAFW Use and Care Manual Page 5

Comments to this Manuals

Related products and manuals for Dishwashers Whirlpool WDF550SAFW