Whirlpool WRS325FDAT Use and Care Guide download pdf (Page 17)

Troubleshooting

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help –

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

If you experience Possible Causes Solution

Dryer Results (cont.)

Odors Recent painting, staining, or varnishing

in the area where your dryer is located.

Ventilate the area. When the odors or fumes are gone from

the area, rewash and dry the clothing.

Steam models only: For steam cycles,

the water is not properly connected

with the dryer.

Make sure water is connected to the dryer. Check that water

inlet hose is connected to both the faucet and dryer’s water

inlet valve. Check that the water supply is turned on.

Odors are left in garments after

wearing.

Steam models only: To remove odors left in garments after

wearing, select Steam Refresh. This cycle is best for reducing

wrinkles and odors from dry loads consisting of wrinkle-

free cotton, cotton-polyester blends, common knits, and

synthetics.

Load too hot Load removed before cooldown

portion of cycle complete.

Allow the dryer to complete the cooldown portion of the

cycle before removing the load.

Using Timed Dry cycle with a high

temperature setting.

Select an Automatic Cycle with a lower heat setting to avoid

overdrying the load.

Dryer Displaying Code Message or Cycle Status Indicator Lights Up

“PF” (power failure) The drying cycle has been interrupted

by a power failure.

Touch and hold START to restart the dryer. NOTE: The

Control Lock function may be enabled when recovering

from a power failure. To unlock the control, touch and hold

CONTROL LOCK for at least 3 seconds.

“L2” Diagnostic Code

(low or no line voltage

condition)

There may be a problem with your

home power supply, keeping the

dryer’s heater from turning on.

The dryer will continue to run when this diagnostic code is

present. Touch any pad to clear the code from the display

and return to the estimated time remaining.

NOTE: This error will only show during the initial installation.

Try the following:

Check to see if a household fuse has blown or circuit breaker

has tripped. Electric dryers use two household fuses or

breakers. Replace the fuse or reset the circuit breaker.

Conrm that the power cord is properly installed. Refer to

the Installation Instructions for details.

Select a Timed Dry heated cycle, and restart the dryer.

If the message persists, consult a qualied electrician.

“F# E#” (F1 E1, F3 E1, etc.)

variable service codes

The dryer is in need of service. If a code beginning with an “F” appears in the display,

alternating between F# and E#, the dryer control has

detected a problem that requires service. Call for service.

Check Vent indicator is lit The lint screen or vent is clogged; the

vent is crushed or kinked or has too

many turns.

The dryer will continue to run when this indicator is lit.

Try the following:

• Clean lint screen.

• Check to see if the vent run from the dryer to the wall is

crushed or kinked.

• Conrm that the vent run from the dryer to the wall is free

of lint and debris.

• Conrm that the exterior vent exhaust hood is free of lint

and debris.

• Conrm that your vent system falls within the

recommended run length and number of elbows for the

type of vent you are using. Refer to “Plan Vent System” in

the Installaton Instructions for details.

• Select a Timed Dry heated cycle, and restart the dryer.

• If the indicator remains lit, have your entire home venting

run cleaned.

“Loc” or “Lc” The Control Lock is enabled. Touch and hold CONTROL LOCK for 3 seconds to unlock

the controls of the dryer. During this time the LED Display

will count down 3-2-1. When the Control Lock is disabled,

the LED Display will clear.

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 39 40

Comments to this Manuals

No comments

Whirlpool WRS325FDAT Use and Care Guide Page 17

Comments to this Manuals

Related products and manuals for Electric laundry dryers Whirlpool WRS325FDAT