4
■ Cooktops with 3-wire cable coming from the cooktop are
rated 240 volt and do not have a neutral (white) wire.
■ The cooktop should be connected directly to the junction box
through flexible, armored or nonmetallic sheathed, copper
cable. The flexible, armored cable extending from the fuse
box or circuit breaker box should be connected directly to the
junction box.
■ Locate the junction box to allow as much slack as possible
between the junction box and the cooktop so that the
cooktop can be moved if servicing becomes necessary in the
future.
■ Do not cut the conduit. The length of conduit provided is for
serviceability of the cooktop.
■ A UL listed or CSA approved conduit connector must be
provided at each end of the power supply cable (at the
cooktop and at the junction box). A listed conduit connector
is already provided at the cooktop.
■ If the house has aluminum wiring follow the procedure below:
1. Connect a section of solid copper wire to the pigtail
leads.
2. Connect the aluminum wiring to the added section of
copper wire using special connectors and/or tools
designed and UL listed for joining copper to aluminum.
Follow the electrical connector manufacturer's recommended
procedure. Aluminum/copper connection must conform with
local codes and industry accepted wiring practices.
INSTALLATION INSTRUCTIONS
Install Cooktop
1. Remove the shipping materials and tape from the cooktop.
Remove the hardware package from inside the bag
containing literature.
2. Using 2 or more people, gently place the cooktop into the
cutout.
IMPORTANT: Check that the front edge of the cooktop is
parallel to the front edge of the countertop. If repositioning is
needed, lift entire cooktop up from cutout to avoid scratching
the countertop.
If cooktop is to be secured to countertop (optional):
1. Remove the coil elements and burner bowls.
■ Push in the edge of coil element toward the receptacle.
Then lift it enough to clear the burner bowl.
■ Pull the coil element straight away from the receptacle.
■ Lift out the burner bowl.
2. Remove the 4 screws from inside each element opening and
lift cooktop from cooktop base.
3. Using 2 or more people, gently place the cooktop in cutout
and determine final location.
NOTE: Make sure that the front edge of the cooktop is
parallel to the front edge of the countertop. If repositioning is
needed, lift entire cooktop up from cutout to avoid scratching
the countertop.
4. Mark on the countertop the location of the 4 mounting holes
at the corners of the cooktop. Set cooktop aside on a
covered surface.
5. Use ¹⁄₈" (3 mm) drill bit and drill 4 pilot holes.
6. Using 2 or more people, gently place the cooktop in cutout so
that the cooktop mounting holes align with the 4 pilot holes.
7. Attach the cooktop base to countertop with the 4 mounting
screws.
8. Reattach the cooktop to the cooktop base using the
4screws.
9. Replace the coil elements and burner bowls.
■ Line up openings in the burner bowl with the coil element
receptacle.
■ Holding the coil element as level as possible, slowly push
the coil element terminal into the receptacle.
■ When the terminal is pushed into the receptacle as far as
it will go, push down the edge of the coil element
opposite the receptacle.
WARNING
Excessive Weight Hazard
Use two or more people to move and install cooktop.
Failure to do so can result in back or other injury.
A. Mounting holes
A
(28 pages)
(16 pages)
(12 pages)
(8 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals