Whirlpool HSCX 10441 User's Guide download pdf (Page 3)

3. SWITCH ON DRYER

• Press the On/O button. An animation appears on the

control panel, and there is a sound. Afterwards the dryer is

ready to be operated.

4. SET THE DESIRED PROGRAMME

• Select programme:

Press the programme symbol on the control panel. Programme

name, default dryness level and default programme duration

appear on the display.

• Change the dryness level, if needed

Press the Dryness level button to select the desired dryness

level:

iron dry

cupboard dry

extra dry

The symbol on the control panel lights up.

• Select options, if needed

Press the options button; the list of available options appears

on the display. Press the UP or DOWN key to navigate through the

list. Press the OK key to select the desired option; a checkmark

appears on the display next to the option name, and the option

symbol lights up.

Some options / functions can be selected by directly pressing the

button:

If an option is not selectable for the programme, it shortly blinks

and switches o again when the button is pressed , and there is a

sound.

Refer to section OPTIONS, FUNCTIONS AND INDICATORS for more

information.

• If “Drying time” or “Airing” programme was selected:

To adapt the drying or airing time,

- press the Drying time button

- adjust the desired drying or airing time by pressing the drying time

button repeatedly, or alternatively by pressing the UP or DOWN key.

Conrm the selected duration by pressing the OK key.

5. START PROGRAMME

• Press and hold Start/Pause until the button lights up solidly.

After a short load sensing phase, the drying process starts.

• The display indicates the remaining programme duration

and the current programme phase.

• The duration can be recalculated and adapted in the course of the

programme. During such phases, the display indicates the sensing

phase, and an animation is shown on the control panel.

6. CHANGE THE SETTINGS OF A RUNNING PROGRAMME, IF

NEEDED

You can still change some settings after a programme was started:

Adjust drying time (only if programme Drying time or Airing is

selected).

Adjust or cancel “Finish in”, if a delay was selected and started.

Add or cancel an option, provided the progress of the programme

still allows it.

• Press the relevant button. The selected setting will blink for a few

seconds.

• While blinking, you can adjust the setting by pressing the UP or

DOWN key. If the value or setting stopped blinking, press the

button again.

• Press the OK key to conrm the modication. If you do not

conrm, the modication will be conrmed automatically – the

modied setting will stop blinking after a while.

The programme will continue automatically.

To change the settings of a running programme or delay, you can

also:

• Press Start/Pause to put the running programme on pause

• Change your settings

• Press Start/Pause again to continue the programme.

7. RESET A RUNNING PROGRAMME, IF NEEDED

• Press and hold the On/O button until the display indicates

that the programme is cancelled.

• Immediately open the door and unload the laundry, so that

eventual heat in the laundry can dissipate.

8. SWITCH OFF THE DRYER AFTER PROGRAMME END

• The display indicates that the cycle has nished. Press On/

O to switch o the dryer. Open the door and take out the

laundry.

• The dryer will switch o automatically in about a quarter of an

hour after programme end, to save energy.

• If not switched o right after programme end, the dryer will

tumble the laundry for about 10 minutes, to avoid creasing.

The display alternately indicates the programme end and the

anti-crease phase. This phase can be ended by either switching of

the dryer as mentioned above, or by opening the dryer door.

9. EMPTY WATER TANK / CLEAN DOOR FILTER / CLEAN

BOTTOM FILTER

• Refer to section CARE AND MAINTENANCE.

1 2 3 4 5 6 7 8

Comments to this Manuals

No comments

Whirlpool HSCX 10441 User's Guide Page 3

Comments to this Manuals

Related products and manuals for Tumble dryers Whirlpool HSCX 10441