Whirlpool WTW8700EC Use and Care Guide download pdf (Page 5)

Control Panel and Features

POWER BUTTON

Touch to turn the washer ON. Touching once while the

washer is on will cancel the current cycle and turn the

washer OFF.

WHAT TO WASH/HOW TO WASH

First select a cycle from the “What to Wash” and then

select the “How to Wash” to get the best combination

cycle available for the type of items you are going to

wash. See “Cycle Guide” for cycle details.

START/PAUSE BUTTON

Touch and hold START/PAUSE button for 3 seconds to begin

the selected cycle; touch again to pause a cycle.

ADD GARMENT

When Add Garment is lit, you may pause the washer, open

the lid, and add items. Touch and hold START to start the

washer again.

TIME/STATUS DISPLAY

The Estimated Time Remaining display shows the time

required for the cycle to complete. Factors such as load

size and water pressure may affect the time shown in

the display. Tightly packed loads, unbalanced loads, or

excessive suds may cause the washer to adjust the cycle

time, as well.

If you have set a delay start to the cycle, the Estimated

Time Remaining display will show the delay time adjusted.

When the cycle is complete, the display will show END until

the lid is opened.

OPTIONS

You may add or remove options for each cycle. Not all

options can be used with all cycles, and some are preset

to work with certain cycles.

DELAY START

Touch Delay Start to delay the start of the wash cycle up

to 12 hours “12H”. Touch Delay Start until a “0H” appears

in the status display to turn off, or touch POWER.

END BEEP

Use this to turn the signal indicating the end of a wash

cycle to low, medium, high, or off.

NOTE: You may also adjust the tones that sound when

a feature, setting, or option is touched. Touch and hold

END BEEP for about 3 seconds to turn key activation

sounds to low, medium, high or off.

STEAM CLEAN

The Steam Clean option adds additional soak and wash

time to many cycles to help remove tough stains, as well

as a steam boost for added cleaning power. Steam Clean

uses a heater within the washer to maintain the selected

temperature setting throughout the wash period. Steam

Clean may be selected as an option with other cycles.

ADDITIVES - OXI

Select the Oxi option so that it is added to the load at the

correct time.

UTILITY TOOLS

Clean Washer

Use this every 30 washes to keep the inside of your

washer fresh and clean. This cycle uses a higher water

level. Use with affresh

Washer Cleaner tablet or liquid

chlorine bleach to thoroughly clean the inside of your

washer. This cycle should not be interrupted. Also

optimizes load sensing for optimal wash performance.

See “Washer Care.”

IMPORTANT: Do not place garments or other items

in the washer during the Clean Washer cycle. Use this

cycle with an empty wash tub.

Rinse & Spin

Combines a rinse and high speed spin for loads

requiring an additional rinse cycle. Also use for loads

that require rinsing only. If you want Drain & Spin select

Rinse & Spin and then deslect Extra Rinse.

EXTRA RINSE

This option can be used to automatically add a second

rinse to most cycles.

PRESOAK

Use this option to add an extra soak period to any cycle

to help loosen tough stains. The washer will ﬁll and then

pause to soak, and then begin the selected cycle.

Not all features and cycles are available on all models.

NOTE: The control panel features a sensitive surface that responds to a light touch of your ﬁnger. To ensure your selections are

registered, touch the control panel with your ﬁnger tip, not your ﬁngernail. When selecting a setting or option, simply touch its name

until the desired section is illuminated.

2 3

5 6

1 2 3 4 5 6 7 8 9 10 ... 43 44

Comments to this Manuals

No comments

Whirlpool WTW8700EC Use and Care Guide Page 5

Comments to this Manuals

Related products and manuals for Washing machines Whirlpool WTW8700EC