Whirlpool HLQB 9.8 LSHI X/HA Instruction for Use download pdf (Page 32)

- Manual calibration: (or upon request) is set in the

conguration menu. This procedure is advised, and may

be started, in case of malfunctioning of the sensor (which,

for example, may occur in case of blackout while cooking

or after a long time since the use).

For the manual calibration, proceed with the steps below:

• with the hood OFF or in standby, the menu is accessed

by pressing the T6 and T7 buttons for a prolonged

time; this is signalled by a sound emitted by the hood

and by the I4 icon lighting up and the writing C1-0

appearing on the display;

• use the buttons T6 and T7 to go through the menu.

Use T6 to go through the various menu items (C1, C2,

C3, C4, etc) and T7 to select them (0, 1 or 0, 1, 2);

• for the manual calibration, access the menu, select

item C4 with T6 and set value 1 with T7. Then press

T1 and wait for the time suggested for the calibration.

Selecting the hob type: the type of hob (electric, induction,

gas) present under the hood is select upon installation. A

complete automatic calibration procedure is carried out

immediately after selecting the hob.

Important: do not force the calibration “upon

request” after selecting the hob as this activates

automatically.

To select the hob, proceed as follows:

• with the hood OFF or in standby, the menu is accessed

by pressing the T6 and T7 buttons for a prolonged time;

this is signalled by a sound emitted by the hood and by

the I4 icon lighting up and the writing C1-0 appearing on

the display;

• use the buttons T6 and T7 to go through the menu. Use

T6 to go through the various menu items (C1, C2, C3,

C4, etc) and T7 to select them (0, 1 or 0, 1, 2);

• to select the hob, access the menu, select item C3 with

T6 and set the value with T7 to 0 if you have a gas hob,

1 if you have a radiant hob and 2 if you have an induction

hob. Press T1 to leave the menu mode and wait the time

needed for the sensor calibration.

Hood type setting

The hood can be set in the ventilation (default) and ltering

operating mode. To change the type proceed as follows:

• with the hood OFF or in standby, the menu is accessed by

pressing the T4 and T5 buttons for a prolonged time; this is

signalled by a sound emitted by the hood and by the I4 icon

lighting up and the writing C1-0 appearing on the display;

• use the buttons T4 and T5 to go through the menu. Use

T4 to go through the various menu items (C1, C2, C3,

C4, etc) and T5 to select them (0, 1 or 0, 1, 2);

• to set the hood type, access the menu, select the item

C6 with T4 and set the value 0 with T5 to set the hood on

ventilation mode or 1 for the ltering mode. Then press T1.

Hood off

The hood can be turned off manually by pressing the T1

button (ON/OFF). If the hood stays on in manual mode, it

turns off automatically after a certain “safety” time. If the

timer is set, the hood turns off automatically when the set

time runs out.

The Automatic mode activates after 10 minutes from the

sensor turning off the hood motor.

Conguration table

Regulation

code

Meaning Explanation

C1 Grease lter timer

It resets the grease

lter timer

C2 Odour lter timer

It resets the odour lter

timer

C3 Hob type

It changes the hob type

for the AUTO sensor. It

may be gas, electric or

induction

C4 Sensor calibration

It calibrates the sensor.

If item 1 is select, the

sensor carried out the

calibration the next

time the hood is turned

C5 Audio levels

If mute, no FB audio is

emitted (not even when

turning ON)

C5 Hood type

Ventilation/Filtering

(Ventilation by default)

Reset to Factory

default

It resets the DGT menu

values to default values

(including installation)

General notes

If the display buttons become locked, unplug and plug

in again the hood from the mains before contacting the

Assistance Service.

Maintenance and care

Caution! Before cleaning or servicing the unit,

disconnect it from the mains by pulling the power plug

or disconnecting the main circuit breaker.

First cleaning

• Remove the protective lm

• Clean with a damp sponge and a little neutral soap

• Rinse off with a damp cloth

• Dry with a soft cloth; if the hood is stainless steel, dry

along the metal's grain

Periodic cleaning

The hood must be cleaned frequently (at least as often as

you service the grease lter), inside and out. Use a damp

cloth and a neutral liquid detergent with lukewarm water.

Do not use abrasive or corrosive products.

Warning: Failure to observe the hood cleaning and lter

cleaning/replacement instructions can result in res. Follow

the instructions carefully. The manufacturer is not liable for

any damage to the motor or res caused by incorrect care

or failure to follow the above instructions.

1 ... 31 32 33 ... 72

Comments to this Manuals

No comments

Whirlpool HLQB 9.8 LSHI X/HA Instruction for Use Page 32

Comments to this Manuals

Related products and manuals for Cooker hoods Whirlpool HLQB 9.8 LSHI X/HA