Whirlpool WEG745H0FS Installation Manual download pdf (Page 4)

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools Needed

Parts Supplied

Check that all parts are included.

■ LP/Natural Gas Conversion Kit

■ #10 x 1⁵⁄₈" (4.1 cm) screws (for mounting anti-tip bracket) (2)

■ Anti-tip bracket (inside oven cavity)

Anti-tip bracket must be securely mounted to the back wall or

floor. Thickness of flooring may require longer screws to

anchor bracket to subfloor. Longer screws are available from

your local hardware store.

■ For Models:

Parts Needed

Check local codes and consult gas supplier. Check existing gas

supply and electrical supply. See “Electrical Requirements” and

“Gas Supply Requirements” sections.

IMPORTANT: When the range is used under microwave models:

JMC82808CB-0, JMV9196CB-0, or YJMV9196CB-0, the Door

Baffle Plate Part Number W10737014 must be ordered and used.

Please reference the “Accessories” section of the User Guide for

contact information.

Optional Parts

To purchase these or any other accessories, please reference the

“Accessories” section of the User Guide for contact information.

■ Side Trim Kits:

⁵⁄₈" (1.7 cm) White - Order Part Number W10675027

⁵⁄₈" (1.7 cm) Black - Order Part Number W10675026

⁵⁄₈" (1.7 cm) Stainless Steel - Order Part Number W10675028

1¹⁄₈" (2.9 cm) White - Order Part Number W10731885

1¹⁄₈" (2.9 cm) Black - Order Part Number W10731886

1¹⁄₈" (2.9 cm) Stainless Steel - Order Part Number

W10731887

■ Backsplash Kits:

High 6" (15.2 cm) White - Order Part Number W10655448

High 6" (15.2 cm) Black - Order Part Number W10655449

High 6" (15.2 cm) Stainless Steel - Order Part Number

W10655450

Location Requirements

IMPORTANT: Observe all governing codes and ordinances. Do

not obstruct flow of combustion and ventilation air.

■ It is the installer’s responsibility to comply with installation

clearances specified on the model/serial/rating plate. The

model/serial/rating plate is located behind the oven door on

the top right-hand side of the oven frame.

■ The range should be located for convenient use in the

kitchen.

■ Recessed installations must provide complete enclosure of

the sides and rear of the range.

■ To eliminate the risk of burns or fire by reaching over the

heated surface units, cabinet storage space located above

the surface units should be avoided. If cabinet storage is to

be provided, the risk can be reduced by installing a range

hood or microwave hood combination that projects

horizontally a minimum of 5" (12.7 cm) beyond the bottom of

the cabinets.

■ All openings in the wall or floor where range is to be installed

must be sealed.

■ Cabinet opening dimensions that are shown must be used.

Given dimensions are minimum clearances.

■ The anti-tip bracket must be installed. To install the anti-tip

bracket shipped with the range, see “Install Anti-Tip Bracket”

section.

■ Grounded electrical supply is required. See “Electrical

Requirements” section.

■ Proper gas supply connection must be available. See “Gas

Supply Requirements” section.

■ Contact a qualified floor covering installer to check that the

floor covering can withstand at least 200°F (93°C).

■ Use an insulated pad or ¼" (0.64 cm) plywood under range if

installing range over carpeting.

IMPORTANT: To avoid damage to your cabinets, check with your

builder or cabinet supplier to make sure that the materials used

will not discolor, delaminate or sustain other damage. This oven

has been designed in accordance with the requirements of UL

and CSA International and complies with the maximum allowable

wood cabinet temperatures of 194°F (90°C).

■ Tape measure

■ Phillips screwdriver

■ Flat-blade screwdriver

■ ¹⁄₈" (3 mm) flat-blade

screwdriver

■ Level

■ Drill

■ Wrench or pliers

■ Pipe wrench

■ ¹⁵⁄₁₆" (2.4 cm) combination

wrench

■ ¹⁄₈" (3.2 mm) drill bit (for

wood floors)

■ Marker or pencil

■ Pipe-joint compound

resistant to LP gas

■ ³⁄₁₆" (4.8 mm) carbide-tipped

masonry drill bit (for

concrete/ceramic floors)

■ Noncorrosive leak-detection

solution

For LP/Natural Gas

Conversions

■ ⁵⁄₈" (1.6 cm) combination

wrench

■ ³⁄₈" (1 cm) nut driver

■ ⁹⁄₃₂" (7 mm) nut driver

■ Masking tape

WEG730H0D

KSGG700E

KSGB900E

MGS8880D

WEG760H0D JGS1450D

Burner Caps 554

Burner Grates 223

Oven Racks 233

1 2 3 4 5 6 7 8 9 ... 47 48

Comments to this Manuals

No comments

Whirlpool WEG745H0FS Installation Manual Page 4

Comments to this Manuals

Related products and manuals for Cookers Whirlpool WEG745H0FS