Whirlpool ADP 301 IX Instruction for Use Page 36

  • Download
  • Add to my manuals
  • Print
  • Page
    / 84
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 35
36
Notes:
Optimumperformancelevels when using the“1Hour” and
“Rapid”cyclescan be achieved byrespectingthe specified
number of place settings.
To reduce consumption even further, only run the dishwasher
when it is full.
Note for Test Laboratories: forinformationoncomparativeEN
testing conditions, please send an email to the following address:
Special wash cycles
and Options
Half Load option
If there are not many dishes to be washed, a half
load cycle may be used in order to save water, electricity and
detergent.SelectthewashcycleandpresstheHALFLOAD
button: the indicator light will illuminate.
PresstheHALFLOADbuttontodeselectthisoption.
Remember to halve the amount of detergent.
Sani Rinse Option
This option allows higher temperatures to be used.
Selectthewashingprogram,presstheSaniRinsebuttonand
the indicator light will switch on. To deselect the option, press
the same button again.
Ideal to clean crockery and feeding bottles.
Warning:thecrockeryandplatescouldbeextremelyhotat
the end of the cycle.
TheSaniRinse option results in lengthening ofthewash
cycle.
Drain out
To stop and cancel the active cycle, the Drain Out
function can be used.
AlongpressofSTART/PAUSEbutton,willactivatetheDRAIN
OUT function. The active cycle will be stopped and the water in
the dishwasher will be drained out.
Child safety lock
Alongpress of HALF LOADbutton, will activate the
SAFETYLOCKfunction.TheSAFETYLOCKfunctionwillblockthe
controlpanel.TodeactivatetheSAFETYLOCK,longpressagain.
Tablet option (Tab)
AlongpressoftheSaniRinsebutton,willactivatethe
TABLET function. This option optimises washing and drying
results. To deactivate the TABLET, long press again.
The “Tablet” option results in a longer wash cycle.
Wash options
The OPTIONS may only be set, changed or reset after the
wash cycle has been selected and before the Start/Pause
button has been pressed.
Only the options which are compatible with the type of wash
cycle set may be selected. If an option is not compatible
with the selected wash cycle
(seeTableofwashcycles)
, the
correspondingled/symbolflashesrapidly3times.
If an option is selected which is not compatible with another
(previouslyselected)option,itwillflash3timesandswitch
off, while the most recently selected option will remain active.
To deselect an option which has been set by mistake, press
the corresponding button again.
Delayed start
The start of the program may be delayed for
a period of time between 0:30 and 24 hours.
1.Select theprogramandanydesired options.Pressthe
DELAYEDSTARTbutton(repeatedly)todelaythestartof
theprogram.Adjustablefrom0:30to24hours.
With each press of the button, the delay start increases by:
0:30 if selection below 4 hours, 1:00 if selection is below
12hours,4hoursifselectionisabove12hours.If24hours
reached, and the button is pressed, the delayed start is
deactivated.
2. Press the START/PAUSE button: the timer will begin
counting down;
3.Oncethistimehaselapsed,theindicatorlightswitches
off and the program begins automatically. If at the time of
thecountdowntheSTART/PAUSEbuttonispressedagain
the DELAYEDSTART option is cancelled and the selected
program starts automatically.
The Start Delay function cannot be set once a wash cycle
has started.
Page view 35
1 ... 35 36 37 ... 84

Comments to this Manuals

No comments