Whirlpool GSIP 300 POWER PT Instruction for Use download pdf

5019 496 01081

GSIP 300 POWER

Before using the dishwasher, read the

installation and maintenance instructions carefully!

1) Programme data obtained in conformity with European standard EN 50242. The data may vary, for example, according to different loads, extra

functions, sensor settings (only with sensor programmes), water supply temperatures, water hardness and power supply voltage.

2) Energy label programme in compliance with EN 50242. - Information for Test Laboratories: for more detailed information on the conditions of the EN

comparison test and other tests, contact the following address: “[email protected]”.

3) The antibacterial action has been shown in collaboration with the Pasteur Institute, Lille (France), in conformity with Standard NF EN 13697 - November 2001.

1. OVERVIEW

Programme selector

START button

The indicator lights up during operation, flashes when a fault

occurs, and goes off at the end of the programme.

START button RESET function:

Press this button for at least 2 seconds to cancel a started

programme and selected extra functions. The main fault

indications (repeated flashing of the START indicator) can be

cancelled by RESETTING. Also refer to section 5 “What to do, in

case of...”.

Power Clean

High pressure with an additional jet for better washing results and

greater bottom rack load flexibility.

With this extra function selected the corresponding symbol

appears on the display.

Detergent setting at first startup and when using a different type of detergent

1. Select the third programme in the relevant table.

2. Press the START button for approx. 7 sec. to change the display.

3. Using the START button, set the required detergent:

The display shows: no symbol = powder detergent (standard supply)

(rinse aid and/or salt indicator active)

= 2 in 1

= 3 in 1 or other combined detergents

(In this way the rinse aid and/or salt indicator is deactivated)

4. Switch the appliance off and then on again. The type of detergent set is shown

on the display.

Fault indication and wash time display

In normal operation it indicates the remaining time (h:mm),

whereas with “Delayed start” selected it indicates the time

remaining until programme start (hh).

With indication “F..”, refer to section 5 “What to do, in case of …”.

Delayed start button

Press the button (repeatedly) to delay the start of the programme.

Adjustable from 1 to 24 hours. With each press of the button, the

delayed start indicator increases by one hour and after 24 restarts

from 00. Then press the START button. The dishwasher will start

after the set time.

Programme progress indicator

Rinse aid level indicator and salt level indicator

They light up when rinse aid or salt need to be added.

Add just before starting a wash cycle.

Half Load/Multizone button

Only load the upper rack or lower rack.

Press once = wash top rack (the indicator/symbol lights up)

Press twice = wash bottom rack (the indicator/symbol lights up)

Press 3 times = Off (Half load/Multizone deactivated).

When washing without the top rack, press the “Half load” (i.e.

“wash bottom rack”) button twice; the indicator /corresponding

symbol lights up.

On / Off button

Prewash Wash Dry

Table 1.1.

Table of programmes

Detergent

dispenser

Consumption

Programmes

Selectable

extra functions

Loading instructions large small Litres kWh Minutes

Steam Sensor + 40-70°C

Normally or very dirty dishes,

including pots and pans.

X X 7-17 0.99-1.75 65-220 ±

Pre-Rinse cold

Dishes to be washed later. — — 4.0 0.03 14 ±

Handwashing 40°C

Slightly dirty items, e.g. glasses

and cups, with a lower pressure

jet.

X — 10.0 0.85 125 ±

Quickwash 40°C

Slightly dirty dishes, without dry

residuals.

X — 10.0 0.65 30 ±

Bio Normal

50°C

Normally dirty dishes.

Energy-saving programme.

X X 11.0 0.98 170 ±

Hygienic +

Normally or very dirty dishes, with

additional antibacterial action. A

programme interruption (e.g. due to

door opening) can compromise

elimination of germs.

X X 13.0 1.50 115 ±

Overnight 55°C

Normally dirty dishes, gentle and

quiet (39 dbA) thanks to the lower

pressure jet.

X X 13.0 1.20 290 ±

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - 1. OVERVIEW

5019 496 010811GBGSIP 300 POWERBefore using the dishwasher, read the installation and maintenance instructions carefully!1) Programme data obtained in

Page 2 - 2. QUICK REFERENCE GUIDE

22. QUICK REFERENCE GUIDEDetailed instructions are given on the following pages; also see section “5. What to do, in case of...”1. Switch on the appli

Page 3 - 3. HOW TO USE THE APPLIANCE

33. HOW TO USE THE APPLIANCEPROGRAMME SELECTIONPress the button “Select programme” or the programme selector to display the selected programme. The ap

Page 4

43. HOW TO USE THE APPLIANCEc. How to adjust the rinse aid dosage regulatorThe rinse aid dosage can be adjusted to the detergent used. The lower the s

Page 5

53. HOW TO USE THE APPLIANCEHOW TO LOAD THE RACKSCUTLERY RACK:May be used in two different positions.In position 2 the upper rack must be lowered (see

Page 6

64. PRECAUTIONS AND GENERAL RECOMMENDATIONS1. PackingThe packaging materials are 100% recyclable and marked with the recycling symbol. .2. Removing t

Page 7 - 5. WHAT TO DO IF

75. WHAT TO DO IF...If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults

Page 8

85. WHAT TO DO IF...Crockery and cutlery ... Possible causes/solutions...are not perfectly clean/have food residues- In the event of frequent use of l

Comments to this Manuals

No comments

Whirlpool GSIP 300 POWER PT Instruction for Use

Browse online or download Instruction for Use for Dishwashers Whirlpool GSIP 300 POWER PT. Whirlpool GSIP 300 POWER PT Instruction for Use User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Dishwashers Whirlpool GSIP 300 POWER PT