Whirlpool WDF530PLYM0 User Manual download pdf

PRODUCT DIMENSIONS

Undercounter Dishwasher

PRODUCT MODEL NUMBERS

WDF510PAY

WDF530PAY

WDF530PLY

WDF530PSY

WDF730PAY

WDF750PAY

WDF780SLY

WDT710PAY

WDT770PAY

WDT790SAY

WDT790SLY

WDT910SAY

WDT910SSY

Electrical Requirements: 120-volt, 60-Hz, AC-only, 15- or

20-amp fused electrical supply. Copper wire only. A time-

delay fuse or circuit breaker and separate circuit is

recommended.

If direct wiring dishwasher: Use flexible, armored or

nonmetallic, sheathed copper wire

with grounding wire that meets the

wiring requirements for your home

and local codes and ordinances.

Use a UL Listed or CSA Approved strain relief.

If connecting dishwasher with a power supply cord:

Use Power Supply Cord Kit (Part

Number 4317824) marked for use

with dishwashers. Follow the kit instructions for installing

the power supply cord.

Power supply cord must plug into a grounded

three-prong, outlet, located in the cabinet next to

the dishwasher opening. Outlet must meet all local

codes and ordinances.

Water Supply Requirements: A hot water line with 20 to

120 psi (138 to 862 kPa) water pressure. Water

temperature must be 120°F (49°C) water at dishwasher.

Use ³⁄₈" O.D. copper tubing with compression fitting or

flexible braided water supply line (Part Number 4396897RP)

(¹⁄₂" minimum plastic tubing is not recommended). Use a

90° elbow with ³⁄₄" hose connection with rubber washer. Do

not solder within 6" (15.2 cm) of the water inlet valve.

Drain Requirements: A new drain hose is supplied with

your dishwasher. If this is not long enough, use a new drain

hose with a maximum length of 12' (3.7 m) (Part Number

3385556) that meets all current AHAM/IAPMO test

standards, is resistant to heat and detergent, and fits the 1"

(2.5 cm) drain connector of the dishwasher.

Make sure to connect the drain hose to waste tee or

disposer inlet above drain trap in house plumbing and 20"

(50.8 cm) minimum above the floor. It is recommended

that the drain hose either be looped up and securely

fastened to the underside of the counter, or be connected to

an air gap.

Make sure to use an air gap

if the drain hose is

connected to house

plumbing lower than 20"

(50.8 cm) above subfloor or

floor.

Use ¹⁄₂" (1.3 cm) minimum

I.D. drain line fittings.

If required, the air gap

should be installed in

accordance with the air gap installation instructions. When

connecting the air gap a rubber hose (not provided) will be

needed to connect to the waste tee or disposer unit.

Because Whirlpool Corporation policy includes a continuous commitment to improve

our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation

Instructions packed with product. Specifications subject to change without notice.

Ref. W10350361A

6/10/11

air gap

Page 1 of 2

1 2

Summary of Contents

Page 1 - Undercounter Dishwasher

PRODUCT DIMENSIONSUndercounter Dishwasher®PRODUCT MODEL NUMBERSWDF510PAYWDF530PAYWDF530PLYWDF530PSYWDF730PAYWDF750PAYWDF780SLYWDT710PAYWDT770PAYWDT790

Page 2 - CABINET CUTOUT DIMENSIONS

CABINET CUTOUT DIMENSIONSNOTE: Shaded areas of cabinet walls show where utilityconnections may be installed.** Measured from the lowest point on the u