Whirlpool WRV996FDEM Use and Care Guide Page 24

  • Download
  • Add to my manuals
  • Print
  • Page
    / 112
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 23
2424
5. To stop dispensing before the selected volume has been
dispensed, remove the glass from the dispenser paddle OR press
MEASURED FILL a second time.
NOTE: If you stop dispensing before the desired volume has been
dispensed, the digital display will continue to show how much
water remains to be dispensed. The display will turn off after 1
minute of inactivity.
6. To select a new volume or start dispensing the same volume
again, you must first finish dispensing the selected volume, or turn
off the Measured Fill feature (either by waiting 1 minute so it will
automatically turn off or by pressing ICE/WATER “Back” to
manually turn it off) and then turn it back on.
The Ice Dispenser
IMPORTANT:
If the ice cubes are hollow or have an irregular shape, it could be
because of low water pressure. See “Water Supply Requirements.”
Ice travels from the ice storage bin through the dispenser chute to
the dispenser. To turn off the ice maker, see “Ice Maker and
Storage Bin.”
The dispenser may continue to make noise and ice may continue
to dispense for several seconds after releasing the dispenser
button or paddle.
To Clean the Ice Dispenser Chute:
Humidity causes ice to naturally clump together. Ice particles can build
up until the ice dispenser chute becomes blocked.
If ice is not dispensed regularly, it may be necessary to empty the ice
storage bin and clean the ice delivery chute, the ice storage bin and
the area beneath the storage bin every 2 weeks.
If necessary, remove the ice clogging the storage bin and delivery
chute, using a plastic utensil.
Clean the ice delivery chute and the bottom of the ice storage bin
using a warm, damp cloth, and then dry thoroughly.
To Dispense Ice:
1. Select the desired type of ice. To switch between cubed ice and
crushed ice, press ICE/WATER.
2. Press a sturdy glass against the dispenser paddle. Hold the glass
close to the dispenser opening so ice does not fall outside of the
glass.
IMPORTANT: You do not need to apply a lot of pressure to the
paddle to activate the ice dispenser. Pressing hard will not make
the ice dispense faster or in greater quantities.
3. Remove the glass to stop dispensing.
NOTE: Ice may continue to dispense for several seconds after
removing the glass from the dispenser paddle. The dispenser may
continue to make noise for a few seconds after dispensing.
The Dispenser Drip Tray
There is an insert in the dispenser drip tray. The insert can be removed
from the drip tray to carry to the sink to empty or clean.
Push down on the rear edge of the insert to tilt up the front edge
for easy removal.
The Dispenser Light
When you use the dispenser, the light will automatically turn on.
To turn on the light when you are not dispensing:
Press LIGHT to toggle through the following choices in a continuous
loop:
OFF (default) - The dispenser light is off
ON - The dispenser light remains on at 100% brightness
DIM - The dispenser light remains on at 50% brightness
The dispenser lights are LEDs that cannot be changed. If it appears
that your dispenser lights are not working, see “Troubleshooting” for
more information.
The Dispenser Lock
The dispenser can be turned off for easy cleaning or to avoid
unintentional dispensing by small children and pets.
NOTE: The lock feature does not shut off power to the refrigerator, to
the ice maker, or to the dispenser light. It simply deactivates the
controls and dispenser paddles. To turn off the ice maker, see “Ice
Maker and Storage Bin.”
Press and hold LOCK for 3 seconds to lock the dispenser.
Press and hold LOCK a second time to unlock the dispenser.
The display screen indicates when the dispenser is locked.
Cut Hazard
Use a sturdy glass when dispensing ice.
Failure to do so can result in cuts.
WARNING
A. Dispenser tray insert
ON DIM
LOCKED UNLOCKED
A
Page view 23
1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 111 112

Comments to this Manuals

No comments