Whirlpool AKT 352/IX Instruction for Use download pdf (Page 3)

SAFEGUARDING THE ENVIRONMENT

• Packaging

The packaging material is entirely recyclable, and is marked with the recycling symbol , which identies it as a type of material that must be sent to local

waste-disposal centres.

• Product

This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE).

By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health.

The symbol on the product, or on the documents accompanying the product, indicates that this appliance may not be treated as household waste. Instead,

it must be delivered to an appropriate collection point for the recycling of electrical and electronic equipment.

Disposal must be carried out in accordance with local environmental regulations for waste disposal.

For further information on the treatment, recovery and recycling of this appliance, contact your competent local authority, the collection service for household

waste or the shop where you purchased the appliance.

DECLARATION OF CONFORMITY

This cooking hob has been designed, constructed and marketed in compliance with:

• safety requirements of EEC “Gas” Directive 90/396;

• safety objectives of the “Low Voltage” Directive 2006/95/CE (which replaces 73/23/CEE and subsequent amendments);

• protection requirements of EEC “EMC” Directive 2004/108/EC;

• requirements of EEC Directive 93/68.

This hob is suitable for contact with foodstuffs and complies with EEC (CE) Regulation n. 1935/2004.

NOTES:

• Improper use of the grids could scratch the hob. Do not position the grids upside down or drag them across the hob.

• If the hob has a glass ceramic top, do not use:

- cast iron griddles or terracotta pots and pans,

- heat diffusers (e.g. metallic mesh),

- two burners for the same pot.

• In the event of prolonged use, additional ventilation may be needed (opening a window or increasing the extraction force of the hood).

• The appliance is not intended for use by persons (children included) with physical, sensory or mental impairment or without experience and knowledge of

the appliance, unless supervised or previously instructed in its use by those responsible for their safety.

• Keep children away from the hob when it is in use and do not let them play with the controls or any other appliance parts.

• WARNING: the protective rubber feet on the grids represent a choking hazard for young children. After removing the grids, please ensure that all the feet

are correctly tted.

• ATTENTION: the glass lid (if provided) may shatter if overheated. Before closing it, make sure that all the burners are off.

After use, make sure that the knobs are in position OFF and close the main gas delivery or cylinder tap.

INSTALLATION

TECHNICAL INFORMATION FOR THE INSTALLER

• This product can be embedded in a worktop 20 to 40 mm thick.

• If there is no oven beneath the hob, insert a separator panel that has a surface at least equal to the opening in the work surface. This panel

must be positioned at a maximum distance of 150 mm below the upper surface of the work surface but, in no case less than 20 mm from the

bottom of the hob. If there is an oven beneath the hob, make sure that it is manufactured by Whirlpool and equipped with a cooling system. The

manufacturer declines all liability if another brand oven is installed beneath the hob.

Before installation, make sure that:

• the local gas delivery conditions (nature and pressure) are compatible with the settings of the hob (see the rating plate and injector table).

• the outer surfaces of the furniture or appliances adjacent to the hob are heat resistant according to local regulations.

• combustion products are discharged outdoors through specic hoods or wall and/or window mounted electrical fans.

GAS CONNECTION

• The gas supply system must comply with local regulations.

• You can find specific local regulations for some countries in the paragraph

“Reference to Local Regulations”. If no information concerning your Country is

given, please ask details to your Installer.

• The connection of the hob to the gas pipe network or gas cylinder must be made by

means of a rigid copper or steel pipe with ttings complying with local regulations,

or by means of a continuous-surface stainless steel hose complying with local

regulations. The maximum length of the hose is 2 linear metres.

• Before connecting the tube to the elbow tting (A), interpose the washer (B) supplied,

in compliance with EN 549.

Attention: if a stainless steel hose is used, it must be installed so as not to touch any mobile part of the furniture. It must pass through an area where

there are no obstructions and where it is possible to inspect it on all its length.

• After connection to the gas supply, check for leaks with soapy water.