Whirlpool WEEA25H0HZ Installation Manual download pdf (Page 15)

4. Attach terminal lugs to line 1 (black), neutral (white), and line

2 (red) wires. Loosen (do not remove) the setscrew on the

front of the terminal lug and insert exposed wire end through

bottom of terminal lugs. Securely tighten setscrew to torque

as shown in the following Bare Wire Torque Speciﬁcations

chart.

Bare Wire Torque Speciﬁcations

Attaching terminal lugs to the terminal block - 20 lbs-in.

(2.3 N-m)

Wire Awg Torque

8 gauge copper 25 lbs-in. (2.8 N-m)

6 gauge aluminum 35 lbs-in. (4.0 N-m)

5. Use a hex or Phillips screwdriver to connect the bare (green)

ground wire to the range with the ground-link screw and

ground-link section. The ground wire must be attached over

the ground-link section and must not contact any other

terminal.

6. Use 3/8" (9.5 mm) nut driver to connect the neutral (white)

wire to the center terminal block post with one of the 10-32

hex nuts.

7. Connect line 2 (red) and line 1 (black) wires to the outer

terminal block posts with 10-32 hex nuts.

8. Firmly tighten hex nuts.

IMPORTANT: Verify the tightness of the hex nuts.

9. Replace lower access cover.

Verify Anti‑Tip Bracket Is Installed

andEngaged

On Ranges Equipped with a Premium Storage Drawer:

1. Slide range into ﬁnal location, making sure rear leveling leg

slides into anti-tip bracket.

2. Remove the premium storage drawer. See the “Remove/

Replace Drawer” section.

3. Use a ﬂashlight to look underneath the bottom of the range.

4. Visually check that the rear range foot is inserted into the slot

of the anti-tip bracket.

On Ranges Equipped with a Warming Drawer

or Baking Drawer:

1. Slide range into ﬁnal location, making sure rear leveling leg

slides into anti-tip bracket. Leave a 1" (2.5 cm) gap between

the back of the range and the back wall.

2. Place the outside of your foot against the bottom front of the

warming drawer or baking drawer to keep the range from

moving, and then grasp the back of the range, as shown.

3. Slowly attempt to tilt the range forward.

If you encounter immediate resistance, the range foot is

engaged in the anti-tip bracket. Go to Step 8.

4. If the rear of the range lifts more than 1/2" (1.3 cm) off the

ﬂoor without resistance, stop tilting the range and lower it

gently back to the ﬂoor. The range foot is not engaged in the

anti-tip bracket.

IMPORTANT: If there is a snapping or popping sound when

lifting the range, the range may not be fully engaged in the

bracket. Check to see if there are obstructions keeping

the range from sliding to the wall or keeping the range foot

from sliding into the bracket. Verify that the bracket is held

securely in place by the mounting screws.

5. Slide the range forward, and verify that the anti-tip bracket

is securely attached to the ﬂoor or wall.

6. Slide range back so the rear range foot is inserted into the

slot of the anti-tip bracket.

7. Repeat steps 1 and 2 to ensure that the range foot is

engaged in the anti-tip bracket.

If the rear of the range lifts more than 1/2" (1.3 cm) off the

ﬂoor without resistance, the anti-tip bracket may not be

installed correctly. Do not operate the range without anti-

tip bracket installed and engaged. Please reference the

“Warranty” section of the User Guide to contact service.

8. Move the range into its ﬁnal location. Check that the range

is level by placing a level on the oven bottom. See the “Level

Range” section.

IMPORTANT: If the range is moved to adjust the leveling

legs, verify that the anti-tip bracket is engaged by repeating

steps 1 to 8.

A. Terminal lug

B. Setscrew

C. Line 2 (red) wire

D. Neutral (white) wire

E. Line 1 (black) wire

A. 10-32 hex nut

B. Line 2 (red) wire

C. Bare (green) ground wire

D. Ground-link screw

E. Neutral (white) wire

F. Line 1 (black) wire

G. Terminal lug

1 ... 14 15 16 ... 44

Comments to this Manuals

No comments

Whirlpool WEEA25H0HZ Installation Manual Page 15

Comments to this Manuals

Related products and manuals for Microwaves Whirlpool WEEA25H0HZ