Whirlpool GBS279PVS - 3.6 Cubic Foot Electric Single OV User Manual Page 20

  • Download
  • Add to my manuals
  • Print
  • Page
    / 27
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 19
81
Dimensions are for planning purposes only. For complete details, see Installation Instructions
packed with product. Specifications subject to change without notice.
SLIDE-IN ELECTRIC RANGE FEATURES & SPECIFICATIONS
Whirlpool Gol
ADA Compliant ADA Compliant
Model No. GY399LXU GY397LXU RY160LXT
Oven
Convection TimeSavor™ Plus
Temperature Management System AccuBake® AccuBake®
Delay Bake Yes Yes Yes
Capacity (cu. ft.) 4.5 4.5 4.3
Hidden Bake Yes
Cleaning System Self-Clean Self-Clean Self-Clean
Auto Self-Clean Latch Yes Yes
Automatic Light Yes Yes
Light Switch Touch-Pad Touch-Pad Rocker
Adjustable Racks
2 Full-Width/
1 Split
2 Full-Width 2 Full-Width
Rack Guides 5 5 5
Glass Door Yes Yes Yes
Window Extra Large Extra Large Extra Large
Cooktop
Ceramic-Glass CleanTop® Yes Yes
Porcelain-on-Steel Cooktop Yes
Surface Elements (2) 6", (1) 6/9",
(1) 9/12" Radiant
(2) 6", (2) 6/9"
Radiant
(2) 6", (2) 8" Coil
Drip Bowls Chrome
Surface Unit Indicator Lights Yes Yes
Controls
Controls H1 H1 M1
General Information
Storage Drawer Yes Yes Yes
Approx. Shipping Weight (lbs.) 200 200 200
Color Availability
*
Q, B, S Q, T, B, S Q, B, S
*
Q White, T Biscuit, B Black and S Stainless Steel
SLIDE-IN ELECTRIC
RANGE REQUIREMENTS
Do not pinch the power supply cord
between the range and the wall.
Do not seal the range to the side
cabinets.
25" countertop depth.
24" base cabinet depth.
36" countertop height.
When installed in a 24" (61 cm) base
cabinet with 25" (63.5 cm) countertop,
front of oven door protrudes 2
1
2" (6.4
cm) beyond 24" (61 cm) base cabinet.
*
Note: 24" (61 cm) minimum when
bottom of wood or metal cabinet is
protected by not less than
1
4" (0.64
cm) flame-retardant millboard covered
with not less than No. 28 MSG sheet
steel, 0.015" (0.4 mm) stainless steel,
0.024" (0.6 mm) aluminum, or 0.020"
(0.5 mm) copper. 30" (76.2 cm)
minimum clearance between the
top of the cooking platform and the
bottom of an unprotected wood or
metal cabinet.
Contact a qualified floor covering
installer to check that the floor covering
can withstand at least 200° F.
Use an insulated pad or
1
4" plywood under
range if installing range over carpeting.
Cabinet opening dimensions shown are for 25" (64 cm) countertop depth,
24" (61 cm) base cabinet depth and 36" (91.4 cm) countertop height.
If installing a range hood or microwave hood combination above the
range, follow the range hood or microwave hood combination installation
instructions for dimensional clearances above the cooktop surface.
SLIDE-IN ELECTRIC
RANGE DIMENSIONS
Models GY399LXU, GY397LXU and RY160LXT
®
30" Slide-in Electric Range
PRODUCT MODEL NUMBERS OVERALL DIMENSIONS
CABINET OPENING DIMENSIONS
COUNTERTOP PREPERATION
GY397LXU
GY399LXU
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specications subject to change without notice.
Electrical: This range is manufactured with the
neutral terminal connected to the cabinet. Use a 3-
wire, UL listed, 40- or 50-amp power supply cord
(pigtail) (see Range Rating chart below). If local
codes do not permit ground through the neutral,
use a 4-wire power supply cord rated at 250 volts,
40- or 50-amps and investigaed for use with
ranges. A time-delay fuse or circuit breaker is
recommended. The model/serial rating plate is
located on the oven frame behind the storage
drawer panel.
Ref. 8101P750-60
04-09-08
The cooktop sides of the slide-in range t over the cutout
edge of your countertop.
If you have a square nish (at) countertop and the
opening width is 30" (76.2 cm), no countertop
preparation is required.
Formed front-edged countertops: Must have molded edge
shaved at 3/8" (1.0 cm) from each front corner of
opening.
Tile countertops may need trim cut back 3/8" (1.0 cm)
from each front corner and/or rounded edge attened.
If countertop opening width is greater than
30" (76.2 cm), adjust the 3/8" (1.0 cm) dimension.
Countertop must be level. Place level on countertop, rst
side to side; then front to back. If countertop is not level,
range will not be level. Oven must be level for
satisfactory baking conditions.
28-5/16"
(71.9 cm)
depth with
handle
35-3/4" (90.8 cm)
cooktop height
with leveling
legs screwed all
the way in
23-3/4"
(60.3 cm)
1" (2.5 cm)
spacer
30-3/4" (78.1 cm)
cooktop width
29-7/8" (75.9 cm) width***
Cabinet opening dimensions
shown are for:
25" (63.5 cm) countertop
depth, 24" (61.0 cm) base
cabinet depth, 36" (91.4 cm)
countertop height
junction box – 5.5" (14 cm min.)
from either cabinet, 10" (25.4 cm)
max. from oor.
23-1/4" (59.1 cm)
opening depth
30" (76.2 cm) min.
cabinet opening width
3/8" (9.5 cm)
radius both
corners
For minimum
clearance to the
top of the cooktop,
see NOTE .*
13" (33.0 cm) max.
upper cabinet depth
30" (76.2 cm)
opening width**
Cabinet door or
hinge should not
extend into cutout.
*
NOTE:
24" (61 cm) min. when bottom of wood or metal cabinet is protected by not less than 1/4" (6.4 mm)
ame retardant millboard covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel,
0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper. 30" (76.2 cm) min. clearance between the top of the
cooking platform and the bottom of an unprotected wood or metal cabinet.
**30-7/8" (78.4 cm) with side panels.
Formed or tiled countertop
trimmed 1/2" (1.3 cm) back
at front corners of
countertop opening.
30-3/4" (78.1 cm)
3/8"
(1.0 cm)
30"
(76.2 cm)
opening
width
Range Rating Specified Rating
of Power Supply
Cord Kit and
Circuit
Protection
120/240 Volts 120/208 Volts Amps
8.8 - 16.5 KW 7.8 - 12.5 KW 40 or 50
16.6 - 22.5 KW 12.6 - 18.5 KW 50
***30-3/4" (78.1 cm) with side panels
®
30" Slide-in Electric Range
PRODUCT MODEL NUMBERS OVERALL DIMENSIONS
CABINET OPENING DIMENSIONS
COUNTERTOP PREPERATION
GY397LXU
GY399LXU
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specications subject to change without notice.
Electrical: This range is manufactured with the
neutral terminal connected to the cabinet. Use a 3-
wire, UL listed, 40- or 50-amp power supply cord
(pigtail) (see Range Rating chart below). If local
codes do not permit ground through the neutral,
use a 4-wire power supply cord rated at 250 volts,
40- or 50-amps and investigaed for use with
ranges. A time-delay fuse or circuit breaker is
recommended. The model/serial rating plate is
located on the oven frame behind the storage
drawer panel.
Ref. 8101P750-60
04-09-08
The cooktop sides of the slide-in range t over the cutout
edge of your countertop.
If you have a square nish (at) countertop and the
opening width is 30" (76.2 cm), no countertop
preparation is required.
Formed front-edged countertops: Must have molded edge
shaved at 3/8" (1.0 cm) from each front corner of
opening.
Tile countertops may need trim cut back 3/8" (1.0 cm)
from each front corner and/or rounded edge attened.
If countertop opening width is greater than
30" (76.2 cm), adjust the 3/8" (1.0 cm) dimension.
Countertop must be level. Place level on countertop, rst
side to side; then front to back. If countertop is not level,
range will not be level. Oven must be level for
satisfactory baking conditions.
28-5/16"
(71.9 cm)
depth with
handle
35-3/4" (90.8 cm)
cooktop height
with leveling
legs screwed all
the way in
23-3/4"
(60.3 cm)
1" (2.5 cm)
spacer
30-3/4" (78.1 cm)
cooktop width
29-7/8" (75.9 cm) width***
Cabinet opening dimensions
shown are for:
25" (63.5 cm) countertop
depth, 24" (61.0 cm) base
cabinet depth, 36" (91.4 cm)
countertop height
junction box – 5.5" (14 cm min.)
from either cabinet, 10" (25.4 cm)
max. from oor.
23-1/4" (59.1 cm)
opening depth
30" (76.2 cm) min.
cabinet opening width
3/8" (9.5 cm)
radius both
corners
For minimum
clearance to the
top of the cooktop,
see NOTE .*
13" (33.0 cm) max.
upper cabinet depth
30" (76.2 cm)
opening width**
Cabinet door or
hinge should not
extend into cutout.
*
NOTE:
24" (61 cm) min. when bottom of wood or metal cabinet is protected by not less than 1/4" (6.4 mm)
ame retardant millboard covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel,
0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper. 30" (76.2 cm) min. clearance between the top of the
cooking platform and the bottom of an unprotected wood or metal cabinet.
**30-7/8" (78.4 cm) with side panels.
Formed or tiled countertop
trimmed 1/2" (1.3 cm) back
at front corners of
countertop opening.
30-3/4" (78.1 cm)
3/8"
(1.0 cm)
30"
(76.2 cm)
opening
width
Range Rating Specified Rating
of Power Supply
Cord Kit and
Circuit
Protection
120/240 Volts 120/208 Volts Amps
8.8 - 16.5 KW 7.8 - 12.5 KW 40 or 50
16.6 - 22.5 KW 12.6 - 18.5 KW 50
***30-3/4" (78.1 cm) with side panels
®
30" Slide-in Gas Range
PRODUCT MODEL NUMBERS OVERALL DIMENSIONS
CABINET OPENING DIMENSIONS
COUNTERTOP PREPERATION
GW397LXU
GW399LXU
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Gas supply: Use 3/4" rigid pipe gas supply line
to the range location. A smaller size pipe on long
runs may result in insufficient gas supply. With
L.P. gas, piping or tubing size can be 1/2"
minimum. If local codes permit, it is
recommended that new flexible metal tubing,
design-certified by AGA or CSA, 1/2-inch or
3/4-inch I.D., be used for connecting the range to
the rigid gas supply line. A 1/2" male pipe thread is
needed for connection to pressure regulator
female pipe threads. An individual manual shutoff
valve must be located in the same room, but
external to the range.
Electrical: A 120-volt, 60-Hz, AC-only,
10-ampere, electrical supply fused on both sides
of the line. A separate circuit is recommended. A
time-delay fuse or circuit breaker is recommended.
Ref. 8113P681-60
04-09-08
The cooktop sides of the slide-in range fit over the cutout
edge of your countertop.
If you have a square finish (flat) countertop and the
opening width is 30" (76.2 cm), no countertop
preparation is required.
Formed front-edged countertops: Must have molded edge
shaved flat 3/8" (1.0 cm) from each front corner of
opening.
Tile countertops may need trim cut back 3/8" (1.0 cm)
from each front corner and/or rounded edge flattened.
If countertop opening width is greater than
30" (76.2 cm), adjust the 3/8" (1.0 cm) dimension.
Countertop must be level. Place level on countertop, first
side to side; then front to back. If countertop is not level,
range will not be level. Oven must be level for
satisfactory baking conditions.
28-5/16"
(71.9 cm)
depth with
handle
35-3/4"
(90.8 cm)
cooktop
height with
leveling legs
screwed all
the way in
23-3/4"
(60.3 cm)
1" (2.5 cm)
spacer
30-3/4" (78.1 cm)
cooktop width
29-7/8" (75.9 cm) width*
Cabinet opening dimensions
shown are for:
25" (64.0 cm) countertop
depth, 24" (61.0 cm) base
cabinet depth, 36" (91.4 cm)
countertop height
junction box – 8" (20.3 cm) to
22" (55.9 cm) from either cabinet,
7" (17.8 cm) max. from floor.
23-1/4" (59.1 cm)
opening depth
30" (76.2 cm) min.
cabinet opening width
For minimum
clearance to the
top of the cooktop,
see NOTE.*
13" (33.0 cm) max.
upper cabinet depth
30" (76.2 cm)
opening width**
Cabinet door or
hinge should not
extend into cutout.
3" (7.6 cm) min.
clearance from
both sides of range
to side wall or
other combustible
material.
18" (45.7 cm)
upper side cabinet
to countertop
*
NOTE:
24" (61 cm) min. when bottom of wood or metal cabinet is protected by not less than 1/4" (6.4 mm)
flame retardant millboard covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel,
0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper. 30" (76.2 cm) min. clearance between the top of the
cooking platform and the bottom of an unprotected wood or metal cabinet.
**30-7/8" (78.4 cm) with side panels.
30-3/4" (78.1 cm)
3/8"
(1.0 cm)
30"
(76.2 cm)
opening
width
*30-3/4" (78.1 cm) with side panels
Page view 19
1 ... 19 20 21 22 23 24 25 26 27

Comments to this Manuals

No comments